Model #PSS26SGPASS GE Side-by-Side Refrigerator

  • Freezer Door
    3 Results
  • Sealed System & Mother Board
    3 Results
  • Fresh Food Door
    3 Results
  • Freezer Section
    3 Results
  • Evaporator Instructions
    3 Results
  • Freezer Shelves
    3 Results
  • Ice Maker & Dispenser
    3 Results
  • Fresh Food Section
    3 Results
  • Fresh Food Shelves
    3 Results
  • Custom Cool
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Out door panel not work Pss26sgpass Ge Refrigerator p series

A:

The main control board sends power and signals to that display board. You could have a failed main control board or a problem with the temperature control board. I recommend that you have a service technician diagnose and repair this problem.

Read More
Lyle W -
Sears Technician
November 12, 2014
Q:

my refregerator is giving out heat. the bottom portion is cold but the upper part is very hot. PSS26SGPASS Ge Refrigerator p series

Q:

I found a burn mark on the main board of the frig (GE), I ordered the new board. How do I know if this is not cause by something else?

A:

The best place to start in a case like this is to tell the expert what was going on with the GE refrigerator that had you looking at the board. Please provide the model number and additional information by clicking on reply to continue the thread. An expert will respond within 24-48 hours.

Read More
Anna T -
July 11, 2012
A:

Model # PSS26SGPASS

Read More
shiro -
July 12, 2012
A:

A burn mark on the control board is sometimes caused by an internal short on that control board instead of a component problem in the refrigerator. If you want to be on the safe side, you can check the resistance through the major loads that are connected to that control board before installing the new one. Be sure that you have the refrigerator unplugged when accessing internal components and making those resistance checks. The first image below shows the wiring diagram for your refrigerator. The second image show the same diagram with the circuits through the compressor and the defrost heater marked in wire colors. I recommend that you check those circuits for resistance. The heater circuit (blue to orange) should measure around 5 to 30 ohms of resistance. The compressor circuit should probably measure between 3 and 10 ohms. (Those resistance values are approximate.) If you measure continuity through those circuits then you should probably be okay by just replacing the control board. I do not know the circumstances that led to your control board failure. If you want to check the other circuits, then you should be able to use the wiring diagram to guide you in that task. If you need more help, reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician examine the refrigerator before replacing that control board, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 16, 2012
A:

Thank you. I got the main board today and installed. How long do I need to run the frig in order the temperature to drop a few degree so I know it is working.

Read More
shiro -
July 16, 2012
A:

You should see a temperature drop in the freezer and refrigerator immediately after replacing that control board if the compressor is running. If that compressor is running but the unit is not cooling, then you have a sealed system problem (bad compressor or lack of Freon). A service technician would need to repair that type of failure since it would involve the recovery and recharge of Freon. If the compressor is not running, you could have a problem with the start relay or the capacity. You could also have a bad compressor.

Read More
Lyle W -
Sears Technician
July 17, 2012
A:

Thank you. The frig is working now.

Read More
shiro -
July 17, 2012
A:

We are glad to hear that it is working. Let us know if you need more help.

Read More
Lyle W -
Sears Technician
July 17, 2012
See more answers

Top Parts