Model #POWER10 JBL Speakers

  • No Image Available - Fidelitone
    3 Results
Find part by diagram >

Question and Answers

Q:

unable to use control panel, frozen with no display WFW70HEBW2 Whirlpool Washer

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you.


TEST #1: ACU Power Check
This test checks for incoming and outgoing power 
to and from Appliance Control Unit (ACU). This test 
assumes that proper voltage is present at the outlet.
1. Unplug washer or disconnect power.
2. Remove top panel to access the machine electronics.
3. Visually check that all connections to the 
interference filter (IF) are securely connected. 
4. Visually check that all connections to the 
ACU are fully inserted. 
5. If both visual checks pass, go to step 6
6. Plug in washer or reconnect power.
7. With a voltmeter set to AC, check for line 
voltage at the input of the interference filter. 
?If line voltage is present, go to step 8.
?If line voltage is not present, verify the continuity of the power cord. If it fails the continuity check, replace the power cord.
8. With a voltmeter set to AC, check for line 
voltage at the output of the interference filter. 
?If line voltage is present, go to step 9.
?If line voltage is not present, replace the interference filter.
9. With a voltmeter set to AC, check for input line voltage to the ACU across pins 1 and 2 of connector J8 AC In (IF filter). 
?If line voltage is present, go to step 10.
?If line voltage is not present, check harnesses and connections between the filter and the ACU. Visually inspect inside connector housing for bent or damaged 
terminals. Repair as necessary.
10. Service LED/DC Supply
The ACU is equipped with a status LED. This LED indicates the health of the ACU. After the ACU is plugged in, the LED will blink for 10 seconds, then it will become solidly lit. 
This LED indicates the functionality of the 
microcontroller and power supply:
•If the LED is not lit,there is not 5 volts 
DC supply to the microcontroller. Replace the ACU.
•If the LED is not solidly lit after 10seconds of blinking upon being powered up, the microcontroller is not responding. Replace the ACU.
•If the LED is solidly lit during washer operation, the ACU is probably OK and the problem is elsewhere.
Check UI input voltage:
Verify that there is 5V between pin 1 and 3 
at J18.
11. Unplug washer or disconnect power.
12. Reassemble all parts and panels.
13. Perform the “Quick Diagnostic Test” 

TEST #2: User Interface (UI)
This test is performed when any of the 
following situations occurs during the User Interface Test:
  • None of the indicators or display turn on
  • Some buttons do not light indicators
  • No beep sound is heard
None of the indicators or display turn on:
1. Unplug washer or disconnect power.
2. Remove the top panel to access the ACU.
3. Visually check that all ACU connectors are 
inserted all the way into the ACU.
4. Remove console assembly. Do not pull on the wires between the console and ACU.
5. Visually check that all UI connectors are 
inserted all the way into the UI. 
6. Visually check that the UI and housing 
assembly is properly inserted into the front 
console.
7. If all visual checks pass, perform TEST #1: 
ACU Power Check, to verify supply voltage and health of microcontroller.
?If supply voltages are present and microcontroller is functioning properly, replace the user interface and housing assembly.
?If supply voltages are not present and Service LED is off or blinking constantly, replace the ACU.
8. Reassemble all parts and panels.
9. Plug in washer or reconnect power.
10. Perform the “User Interface Test”.

Some buttons do not light indicators:
1. Unplug washer or disconnect power.
2. Remove the top panel to access the ACU and User Interface (UI).
3. Visually check that the UI and housing 
assembly is properly inserted into the front console.
4. If visual check passes, replace the UI and housing assembly.
5. Reassemble all parts and panels.
6. Plug in washer or reconnect power.
7. Perform the “User Interface Test” 
 
No beep sound is heard:

NOTE: This washer has a feature to turn off the 
button sounds that the user may have activated. 
Press and hold CYCLE SIGNAL for more than 
3 seconds to restore beep sounds. If no beep 
sound persists, follow these steps:

1. Unplug washer or disconnect power.
2. Remove the top panel to access the ACU.
3. Visually check that all ACU connectors are inserted all the way into the ACU. 
4. Remove console assembly. Do not pull on the wires between the console and ACU.
5. Visually check that all UI connectors are inserted all the way into the UI. 
6. If all visual checks pass, replace the UI and housing assembly.
7. Perform the “User Interface Test” 

USER INTERFACE TEST:
NOTE: The Service Diagnostic mode must be activated before entering the User Interface Test.
Active Fault Code Display in User Interface Test
If the display begins flashing while in User Interface Test, it is displaying an active fault code. Active fault codes are codes that are currently detected. Only one active fault code can be displayed at a time.
Entry Procedure
Press and release the 1st button used to activate 
Service Diagnostic mode. All console indicators 
turn on and “888” or “88” is displayed.
User Interface Test
Pressing each button will turn off its 
corresponding indicator(s) or display segment 
and sound a beep.
Rotating the cycle selector knob turns off each 
corresponding cycle indicator.
? If indicators do not turn off and beep after 
pressing buttons and rotating the cycle 
selector knob, go to TEST #2: User Interface.

Exit Procedure

To exit User Interface Test, press and hold the 
1st button used to activate Service Diagnostic 
mode for 5 seconds, or press the POWER button once or twice.

ACTIVATING SERVICE DIAGNOSTIC MODE
1. Be sure the washer is in standby mode 
(plugged in with all indicators off). 
2. After initial power is applied, wait 
30 seconds before activating Service 
Diagnostic mode.
3. Select any three (3) buttons (except 
POWER) and follow the steps below, using 
the same buttons. Remember the buttons 
and the order that the buttons were pressed.
Within 8 seconds,
• Press and Release the 1st selected button,
• Press and Release the 2nd selected button,
• Press and Release the 3rd selected button;
• Repeat this 3 button sequence 2 more times.
4. If the Service Diagnostic mode has been 
entered successfully, all indicators on the 
console are illuminated for 5 seconds with 
“888” or “88” showing in the Estimated Time 
Remaining (Whirlpool) or Estimated Cycle 
Time (Maytag) seven-segment display. If 
there are no saved fault codes, all indicators 
on the console will momentarily turn off, 
and then only the seven-segment display 
will come back on and display “888” or “88”.
NOTE: The Service Diagnostic mode will time 
out after 10 minutes of user inactivity, or shut 
down if AC power is removed.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 12, 2015
Q:

Replacement drive belts (part no. 37x118MA) for mower model 536.885600 are too short as compared to the original drive belts labeled Gates Hi Power 10x450.

A:

The belt not fitting can be very frustrating. I did some research on your model number and part number but was not able to find a solution. Your expert will be able to help answer your question. It may take two business days for your expert to reply. I do hope that everything works out on the mower.

Read More
Marc -
May 24, 2013
A:

Have the belts been changed on this before? I've never seen a Gates belt come new on a mower. Not in 20 years of doing this have I seen that before.

I show the same part numbers for the belts that you do. I'm going to contact the manufacturer and see if they can give us some clarification on this.

I will post back what I find out from them on this and we'll see what we can do to get this working.

Thank you for using Manage My Life!

Read More
Wade_B -
Sears Technician
May 27, 2013
A:

same issue here. Bought the belts listed, but no way they every fit this model mower. Anyone ever figure out what does fit?

Read More
Lori -
June 28, 2015
See more answers
Q:

F01 Error code WED8410SW2 Whirlpool Residential dryer

A:

Thank you for choosing SearsPartsDirect. I will be more than happy to assist you with your Whirlpool washer.

From the information you have provided above, I can understand the frustration of having your washer malfunction, after researching model number WED8410SW2. The error code F01 indicates an issue with the main control board. since you’ve unplugged and the code is still there I would suggest replacing the board to get the code cleared and the issue resolved.

I hope you found this information useful. Again thank you for choosing Sears, we appreciate your business, have a great day.

*Safety disclaimer before you try and repair the unit make sure the power supply is disconnected. There may be sharp parts to the unit that can cause injury to you if not careful. If you don’t not feel comfortable checking this yourself you can request a technician by visiting www.SearsHomeService.com*

Read More
Benny23 -
Sears Technician
May 26, 2015