Model #PLEB30S8CCC FRIGIDAIRE Built-In Oven, Electric

  • Control Panel
    3 Results
  • Body
    3 Results
  • Door
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

bottom element is not heating up PLEB30S8CCC Frigidaire Electric oven

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when the bake element isn't working on the range.

Glad to help out.   Im  looking at your Frigidaire model number PLEB30S8CCC.

 The bottom element, aka the bake element, is available to order and they do go bad.   You can always check with a meter for verification.   Mostly they go bad right around Thanksgiving.   On the link below is the bake element to click on.

Bake element for the model PLEB30S8CCC 

If you have further questions please let me know.

Thanks for choosing Sears PartsDirect.com 

 

Read More
Larry L -
Sears Technician
October 08, 2013
Q:

How to install electronic control board in a Frigidaire wall oven?

A:

I understand that you want to install the electronic control board in your Frigidaire wall oven. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina -
February 23, 2013
A:

Alina, Although I appreciate the links and had already seen both, they both refer to NON-wall ovens.. That is, they are ovens that are on the floor; thus would could get access but simply moving the oven as a whole. My question is for a WALL oven. On past questions, I saw a 'Ken S.' had answered some questions, including the one for this site above. I hope he can review my question and have the answer. Thanks... looking forward to THE answer.....!!! - Ron

Read More
RonnieG -
February 23, 2013
A:

I am not sure whether you will be able to release the console on that model of Frigidaire wall oven. You can open the oven door and look for screws on the bottom of the trim that is mounted below the console. If you find screws in that area and remove them, then you may be able to release console (with that top trim piece removed). Be sure that you shut off the house circuit breakers for the wall oven to completely disconnect electrical power before accessing internal components.

 

If you are not able to release the console in that manner, then you will probably need to pull the oven out of the counter at least far enough to access the console cover that is shown as Key 131 in the second image below. The first image shows the console parts. You may be able to use that information and your personal examination of the parts to access the control board. Here is a link for the installation guide that you can use to help you pull the oven out of the counter: Frigidaire Wall Oven PLEB30S8CCC Installation Instructions.

 

This information may help you access and replace that control board. If you need more help with that task, reply with additional details and we will try to assist you further.

 

You indicated that you tested the bake element. It appears that you may be indicating that you do not have continuity through that component. I am not sure based on your details. If that element does not have continuity, then it will need to be replaced. You should measure between 10 and 40 ohms of resistance through that element.

 

You can view parts drawings and order parts on this page: Frigidaire Wall Oven Model PLEB30S8CCC Repair Parts. 

 

If you need more assistance, let us know.

 

If you get to the point where you need to have a service technician install the control board and repair the oven, you can schedule service through this link: Sears Home Services Oven, Cooktop, and Range Repair and Troubleshooting. 

Read More
Lyle W -
Sears Technician
February 25, 2013
A:

First of all, BIG THANKS TO LYLE for his detailed answer and assistance. I did have to pull the oven from the wall and take out a LOT of screws to get to the control board. I opened the console cover as you said. Eventually I had the control board out, took a picture to confirm where all of the wires went, remove those connectors and replaced back in order. It took a while to get everything back in order I had originally taken out so luckily, once the power came back on, everything worked. As noted, I did test the bottom baking element initially, there was no continuity so did buy a new element BEFORE I bought control board. The new element did not work so figured a voltage spike when the old element went out hit the control board. Very happy when new element worked and the new control board was able to raise the temp as it should. Again, LYLE IS THE MAN. Thank for your time in answering these questions. -- Ron

Read More
RonnieG -
February 28, 2013
See more answers

Top Parts