Model #PDW7300N15WW GE Dishwasher

  • Escutcheon & Door Assembly
    3 Results
  • Body Parts
    3 Results
  • Upper Rack Assembly
    3 Results
  • Lower Rack Assembly
    3 Results
  • Motor-pump Mechanism
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

We have an unsightly control panel on our GE dishwasher.

A:

I know this type of information can be very helpful for you to have. While you are waiting for your expert answer, I did some research on the unit. I was unable to locate information that would be helpful with regards to your question at this time. Your expert will answer within 24-48 hours with detailed information. Thank you for using Manage My Life.

Read More
Alina -
June 07, 2013
A:

I know that it can be very difficult to have issues with your dishwasher. However, the seals on the control panels is not something that can be replaced. These are put on at the factory level and will not fit properly outside of this process. If you would like to fix this, you would need to replace the whole panel. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 07, 2013
See more answers
Q:

GE dishwasher leaking from flood switch

A:

When a problem is intermitten, like the flooding with the GE dishwasher, it makes it harder to figure out what the cause is and how to fix it. That is why there are experts waiting to assist, as you will see in the link provided below. Some one has asked a similar question on their dishwasher. This may be helpful while waiting for a response on your specific model. If service is needed, that link is also provided.

Read More
Anna T -
November 14, 2012
A:

Intermittent problems are always difficult to pin down. A crack in the float stem/tub would cause a leak but I would expect it to leak every wash. The first image below shows the float stem. To much water might cause this problem. The 2nd image contains information about the correct water level. Check for a crack around the float stem and check the water level and let me know what you find and we'll discuss the next step.

Read More
Fred M -
Sears Technician
November 14, 2012
A:

We have checked the water level and it is not overfilling. We do not see any cracks around the float stem/tub. It leaks from the flood switch area at the end of the initial rinse when water starts to discharge before going into the wash cycle.

Read More
thewatts -
November 15, 2012
A:

If the unit is leaking durin the drain cycle then I suggest you remove the two screws holding the kickplate on and take a look to see if you can visually verify the source of the leak.

Read More
Fred M -
Sears Technician
November 17, 2012
A:

We have already done that - that's where we see the water coming from the flood switch area. It is still sporadic although happening more frequently now. Sometimes just a small amount of water, sometimes it pours out. For example, last night as it emptied from its initial rinse water poured out. I hit the reset to stop the machine, restarted it from the beginning and it did not leak at all.

Read More
thewatts -
November 17, 2012
A:

Where was the water pouring out from? The door? If the water level is high enough the water might exit through the float stem. If it only happens in the drain cycle then a restricted drain might cause the water to back up and out the door or stem.

Read More
Fred M -
Sears Technician
November 17, 2012
A:

Update .... the problem took a turn for the worse when water started pouring out of the machine and we could not stop it from filling - even with the power off! Realized that the problem was probably the inlet valve which we changed and this seems to have resolved the issue. As we had already ordered a new flood switch we figured we may as well change that too. Thanks for your help.

Read More
thewatts -
November 21, 2012
A:

If the water continued to fill even with the power off the the valve was the problem. Good job and I'm glad you got it fixed especially during the holidays.

Read More
Fred M -
Sears Technician
November 25, 2012
See more answers

Top Parts