Model #NAV5800AWW AMANA Residential Washers

  • Control Panel
    3 Results
  • Top And Door Switch
    3 Results
  • Cabinet & Base
    3 Results
  • Mixing Valve And Hoses
    3 Results
  • Tubs (inner & Outer)
    3 Results
  • Motor, Pump And Idler Assembly
    3 Results
  • Transmission & Brake
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
  • Tub, Inner & Outer (series 12)
    3 Results
Find part by diagram >

Question and Answers

Q:

how to replace belt NAV5800AWW Amana Amana laundry

A:

I added a link with instructions for removing the pump and motor.

I hope this is helpful.

Read More
Joey S -
Sears Technician
January 29, 2015
Q:

Why is my Amana washer not spinning or agitating?

A:

It sounds like the belt has come off of the idler pulley or motor pulley. I would recommend checking the belt first. Other possibility; transmission.

Read More
biker dave -
Sears Technician
A:

I have the Amana NTW5205TQ0 that will not agitate or spinn. I checked the direct drive and it was not broken. I changed the timer and it still will not work.

Read More
Ronald -
February 16, 2013
See more answers
Q:

Why does my washer drain while filling?

A:

It is definitely puzzling having a washer drain at the same time that it is filling and I understand why you would want this issue fixed as soon as possible. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
February 16, 2012
A:

Alina, thank you for the links. They speak about a siphoning problem which I don't think I have. My drain pipe is high enough. It is not sealed which could cause it to siphon if it was. The hose is only a few inches down the pipe so there is no way it could cause it to siphon. You are right it is puzzling!

Read More
Kenneth -
February 16, 2012
A:

Thanks for contacting ManageMyLife.com. I understand how frustrating it is having the washer keep stopping and refilling with water. We are here to help. The washer losing the water while agitating can have several causes. They are as follows.

  1. The washer is leaking water on the floor.
  2. The drain pump is running while agitating.
  3. The drain hose is not 39" high.
  4. The drain hose has been stuffed too far into the drain pipe causing a siphoning condition.
  5. The drain hose is sealed where it enters the drain pipe.
Since you said the drain hose is high enough and not sealed at drain pipe, I suspect the answer is that it is stuffed too far into the drain pipe. Therefore you need to pull up the drain hose and reinstall it making sure it is no move than 6" into the drain pipe. I hope this helps.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. You may visit SearsHomeServices.com and click on the red Start now button.

Please feel free to let me know if you need further assistance. We are always here to help.

Thank you for using ManageMyLife.com.

Read More
John H -
Sears Technician
February 17, 2012
A:

Thanks for the help John. The hose is only a few inches down the pipe so that isn't it. I think #2 might be the problem. Watching it more we realized that it is only draining while it is agitating. Something that complicates our problem is that we are missionaries in Nicaragua and can't find any parts here. We hope to diagnose the problem and pick up the parts in Florida in a few weeks. So, if it is #2, what do I do? Do I need a new pump? Someone here suggested a new timer? Thank you much!

Read More
Kenneth -
February 17, 2012
A:

Kenneth. There is a way to tell if that is happening by measuring the voltage to the pump while it agitating.You can measure the voltage with a multimeter. You should have zero voltage during agitating. If you have 120vac at pump during agitation that would be a indication of a timer contact sending voltage at the wrong time. That would indicate a bad timer and it would need to be replaced. The pump is good as it only responds when voltage is applied. Also recheck drain hose height. The part number for the timer is 27001088. I hope this helps

Read More
John H -
Sears Technician
February 18, 2012
A:

Thank you John. This makes sense and helps me a lot!

Read More
Kenneth -
February 18, 2012
A:

Kenneth, I thought I'd jump in since it's such any interesting problem. One thing is the pump on this particular model attaches directly to the motor and doesn't require voltage to tun. In theory when the motor runs one dirsection it agitates and when it reverses direction it should drain and spin. If this is not a siphon problem then the timer or pump is at fault. What happens when the machine transitions from agitation to drain and spin? Does it drain then also and does it spin? Let me know and I'll try to provide further assistance.

Read More
Fred M -
Sears Technician
February 18, 2012
A:

Let me know also if ther is a meter available and if anyone feels comfortable using it. The timer is ususally what determines the direction of the motor. Are you getting voltage from a generator or from the grid.

Read More
Fred M -
Sears Technician
February 18, 2012
A:

Hello Fred, thanks for jumping in. Our electricity is on a grid. Of course that is a problem because of the great fluctuation that we have. Though all our electronics are on voltage regulators, most burn up within a few years anyway. I don't know anyone with a meter that I would call competent to use it. The washer fills and begins to drain when it goes into the agitation mode. After it drains a bit it will start to fill again all the while it agitates. If we advance the timer manually to the spin cycle, it spins but stops draining.

Read More
Kenneth -
February 18, 2012
A:

Does the washer also drain in spin? During agitation, the motor runs in a counterclockwise direction. After the wash agitation is completed, the timer advances into the first spin. During spin, the motor reverses turning in a clockwise direction to spin the water out of the washtub. Try and verify the motor direction during the agitation ans spin cycle. My feeling is the timer/voltage is messed up causing this problem.

Read More
Fred M -
Sears Technician
February 18, 2012
See more answers

Top Parts