Model #MVWC300VW1 MAYTAG Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Controls And Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Agitator just goes round and round, Maytag MVWC300VW1

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Let’s see what we can do for you.

The next thing that would need to be replaced would be the cam bearing that the agitator dogs sit into. This should of been replaced all at once when replacing the dogs, because the cam is what the dogs lock into. If this cam is stripped then the agitator won’t work correctly.

Hope this information has helped you. If you are not comfortable doing this repair you can click here to schedule a technician or call toll free 1-800-469-4663. Again, thank you for choosing SearsPartsDirect.com.

 

Read More
JeffwallaceIII -
Sears Technician
July 18, 2015
Q:

shift actuator MVWC300VW1 Maytag Washer

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number MVWC300VW1 and this washer will function differently than the washers we are all used to. When the START button is pressed, the washer will first perform a self-test on the lid lock mechanism. You will hear a click, the basket will make a slight turn, and the lid will unlock briefly before locking again. Once the lid has locked the second time, the washer will slowly spin the dry load to estimate the load size, and begin adding water. The washer will then move the load briefly, pause to allow water to soak in to the load, and resume adding water. This process may repeat until the correct amount of water has been added for the load. You may also hear water flowing through the dispenser, adding detergent to the load. NOTE: The sensing light may also come on during the Soak and Wash portions of the cycle. This is normal. 


If the washer never advances past the lid lock and unlock, the first thing I recommend is checking for error codes. This washer has a test routine you can run that will help in the diagnosis of any problems the control detects. If the control detects a problem it will identify it with an error code. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
January 30, 2015
Q:

humming motor MVWC300VW1 Maytag Washer

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your washer. Upon researching model MVWC300VW1; it sounds like a part inside the agitator or connected to the agitator is putting stress on the motor. The agitator should be disassembled and see if there is any marks of rubbing. Then run just a spin cycle without water to see if it will start freely.  

Thank you for choosing Sears. We appreciate your business. Have a great day.    

 

Read More
Jeff Wallace Jr -
Sears Technician
January 15, 2015

Top Parts