Model #MJ9200W MAJESTIC APPLIANCE Residential Washers

  • Cabinet Parts
    3 Results
  • Tub/drum Asy
    3 Results
  • Electric Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

mj9200w front load washer MJ9200W Majestic Appliance Washer

A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer is not working properly.

 I suspect the lid switch could be the issue since the unit is not filling or starting. 

Most of the parts are no longer available for this model due to the age of the product. The lid switch is no longer available. You would have to find a used part in order to replace the switch if it was the issue.

 
A. The appliance is not working 
 
Possible causes: 
 
1.The socket is not the required one, or that connection is loose. 
 
2.The door is not properly closed or the switch of micro delay in poor contact. 
 
3.The plug wire of the motor is in poor contact, or the motor broken. 
 
4.Malfunction of electronic module. 


Troubleshooting 
 
1.Check the socket and plug to make sure they are properly connected. 
 
2.Check whether the micro delay switch is in good contact with" On-position". If yes, insert the terminal firmly to provide good connection. 
 
3.The electronic module controls the rotary speed and direction of the motor. In  case of failure, check the wiring or replace the electronic module. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

Read More
Natasha12 -
Sears Technician
May 28, 2015
Q:

Majestic washer

A:

Thank you for your question.  If the washer will spin then the door lock and motor and belt are okay.  If the washer will spin but will not agitate then I suspect the timer is at fault.  If the washer will spin then the speed control, door lock and motor are okay.  This particular washer is based upon the Frigidaire front load washer.  Your best bet would be to have the washer repaired in your home by a technician.  Here is the link.  Sears Home Services Washer Repairl.   I hope this helps. 

Read More
Fred M -
Sears Technician
November 20, 2013
Q:

We just had to replace the hose that connects the detergent tray to the drum and now the washer will not fill.

A:

Good morning... This may be something you can fix yourself... Manage My Life customarily gives instructions on how to fix practically anything. Once diagnosed, request step by step instructions and MML will provide them free of charge. I did a search to look for a link that would be close to describing what you're experiencing. The link that I have provided is the closest I can find.  Click here to view the link.   Keep in mind that an expert will review your question and get back to you within two business days. I hope this link helps you and have a nice day.

Read More
Henry -
July 12, 2013
A:

Thank you for the response. I will read this over in detail. The symptoms sound similar to what we are experiencing at this time.

Read More
john -
July 12, 2013
A:

Thank you for your question.  I can likely help you with this problem with your Majestic MJ9200W Front Load Washer.  Changing the hose should not have caused a fill problem.  I suspect the problem is a loose wire from the control.  There are two water valves.  It is unlikely both the hot and cold would fail at the same time.  I believe there is a red wire from the timer/control that powers the water vavles.  You can also check the connections on the pressure switches.  There are two pressure switches on this machine.   You can remove the three screws holding the rear panel to access the pressure switches.  I hope ths helps.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
July 13, 2013
A:

Thank you for your question.  I can likely help you with this problem with your Majestic MJ9200W Front Load Washer.  Changing the hose should not have caused a fill problem.  I suspect the problem is a loose wire from the control.  There are two water valves.  It is unlikely both the hot and cold would fail at the same time.  I believe there is a red wire from the timer/control that powers the water vavles.  You can also check the connections on the pressure switches.  There are two pressure switches on this machine.   You can remove the three screws holding the rear panel to access the pressure switches.  I hope ths helps.  You can reply below with any additional details for further assistance. 

Read More
Fred M -
Sears Technician
July 13, 2013
A:

Sears appliance repair came out to assess the issue yesterday. It appears that the replacement hose is the problem because it is a different shape than the original hose. After an hour of having the washer connected to a diagnostic machine, bypassing the various controllers, and spending time with his support group on the phone it was determined that the new shape of the hose is causing a pressurization issue in the washer. Unfortunately, the exact hose that we need, Majestic part # 17-1328 is no longer being found. We assume that there is some form of modification that needs to be done to get the issue resolved using the new replacement hose, which looks nothing like the original, but we can not find anything on the internet from people who have experienced the same issue. I have attached a picture of the original hose just in case someone knows where I can locate it.

Read More
john -
July 16, 2013
A:

If I understand correctly the replacement hose that should work does not and the original hose is no longer available. I have a hard time believing the hose is causing the problem. Even if the new hose was kinked or to small causing back pressure it should still allow some water past to the tub. Try turning the water supply spigots down for less pressure and see if that helps.

Read More
Fred M -
Sears Technician
July 17, 2013
See more answers