Model #MHWE500VW00 MAYTAG Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Dispenser Parts
    3 Results
  • Tub And Basket Parts
    3 Results
  • Steamer, Pump And Motor Parts, Optional Parts (not Inc
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

May Tag error F35 MHWE500VW00 Maytag Residential washer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when having trouble with the washer and getting the F35 error code.
 
Glad to help out.   Im  looking at your  Maytag Washer model number  MHWE500VW00.

Let me get you all the information that I can from the Service book of your model 
 MHWE500VW00 washer.
 
F 35 = ANALOG PRESSURE SENSOR FAILURE:

If this failure is displayed, the Central Control Unit has detected a malfunction of the analog pressure sensor.

POSSIBLE CAUSES/PROCEDURES

1.  Check if pressure hose is fixed correctly and without holes or damage.

2.  Check if the air trap is not blocked.

3.  Check if the hose is not blocked.
 
Service
If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: www.SearsServiceCrew.com
 
Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
June 24, 2014
Q:

What does F 35 Mean on Washer

A:

The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor. This error code can be caused by a problem with the air pressure tube between the bottom of the washer tub and the analog pressure sensor. If you are able to unplug the washer and check this air pressure tube, you may be able to resolve this problem. The analog pressure sensor can be accessed by pulling off the top panel of your washer. Remove the screws at the very back of the top panel and then pull it back slightly and then up and off of the washer. The analog pressure sensor is Key 38 in the first image below. With the washer unplugged, check the connection of the air pressure tube to this component. Check the entire air tube down to its connection to the bottom of the washer tub. You will likely need to remove the back panel of the washer to check the entire air pressure tube. If you find a kink, tear, hose or loose connection in the air pressure tube, then this is the likely cause of your F35 error code. If the air pressure tube appears to be okay, then you will likely need to replace the analog pressure sensor. If the problem still exists after replacing this component, then the main electronic control board for the washer will need to be replaced. If you are not completely confident in your technical ability to safely access and check these components, I recommend calling a service technician to diagnose and repair the washer.

This information was based on the general description of the washer model that you provided (Kenmore Elite front load washer). There are several different models of this washer. I am not aware of other uses of the F35 code on the various models. If you intend to diagnose and repair this problem yourself, I recommend resubmitting your question with the full model number of your Kenmore washer so that we can verify this technical information using your model number.

Read More
Fred M -
Sears Technician
May 14, 2010
A:

Error Code F 35. Model #110.46752701.Thanks for responding to my question.

Read More
Cindy -
May 14, 2010
A:

I want to thank you for your advice. Will give it a try ...........

Read More
mtiwife -
May 14, 2010
A:

thank you i will try

Read More
jerjohnwitherspoon_ -
December 07, 2010
A:

i cant see the image of the key 38

Read More
dave -
May 18, 2011
A:

Here is that parts image that is missing from the expert answer provided above.

Read More
Lyle W -
Sears Technician
June 09, 2011
A:

what does the air presure tube look like

Read More
connie -
June 22, 2011
A:

The images below show that air pressure hose. It is a black hose connected to that pressure switch. The other end is connected to the air trap on the bottom of the washer tub.

Read More
Lyle W -
Sears Technician
June 23, 2011
A:

The model of my frontloading washer is 11047791700.

Read More
Steven -
August 07, 2011
A:

Hello Steven. Thanks for providing that model number. The F35 code on your washer indicates a failure of that water level pressure sensor as noted in the above thread. The part number for that component in your washer is W10415587. You can order that part by clicking on the Find Parts link at the top of this page. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
August 08, 2011
See more answers

Top Parts