Model #MGS5770ADC MAYTAG Slide-In Range, Gas

  • Top Assembly (ada, Adb, Adw, Adc)
    3 Results
  • Body
    3 Results
  • Oven/base
    3 Results
  • Gas Controls
    3 Results
  • Wiring Information
    3 Results
  • Door/drawer (adc)
    3 Results
Find part by diagram >

Question and Answers

Q:

How access electronic control maytag mgs5770adc gas range

A:

I can understand your need for proper instruction regarding access to your electronic control board. I did a search using your model number and located a link that is similar to the symptoms you're experiencing. Click on the link below to view the page. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this information will be helpful and have a nice day.

Read More
Henry -
August 08, 2013
A:

Thank you for your question. I am assuming you wish to test or replace the electronic control. I was able to locate a video that provides general information on accessing and testing the control. The diagrams and parts for your model can be viewed at Sears Parts Direct . If further help is needed,please reply with additional detail.  Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
August 08, 2013
See more answers
Q:

Oven valve MGS5770ADC

A:

A oven is a very important appliance we use in a daily basis. I am sorry to hear that you are having problems with it, specially on this holiday season. Looking on the site I came upon some information that can be very helpful. I have attached the links below. Hope they help!

Read More
maira -
December 24, 2012
A:

You could have a problem with the igniter on that bake burner. Here is a link for a brief video that explains the operation of the oven burner ignition system on your Maytag range: Gas Ignition Operation . If the bake burner igniter glows when you set the oven in the bake mode, then the oven safety gas valve is probably okay. If you suspect that the igniter on bake burner is bad, then you can switch it out with the broil igniter since those components are identical. If the bake burner lights properly after switching those igniters, then the bad igniter will need to be replaced. You can order that igniter from this page: Igniter for Maytag Range Model MGS5770ADC . Be sure that you unplug the range or shut off the house circuit breaker to completely disconnect electrical power before accessing and replacing internal components. Shut off the gas supply as well when accessing and replacing internal components.

If the igniter does not glow on that bake burner then you could have a bad igniter, a failed safety gas valve, a defective electronic control board or a wiring failure in that ignition circuit.

Reply with additional details if you need more help with this problem.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
December 26, 2012
See more answers
Q:

control panel blinking

A:

It would be disappointing to complete a repair and have no sign of success. While you wait for the expert to review your model you might check a previous expert post with a similar issue and a suggestion for a quick check. I attached that link below.

Read More
Barbara H. -
July 21, 2011
A:

One thing is that the model number you submitted MCS5770ADC did not bring up anything. I did find a Maytag gas range model MGS5770ADC. Is it possible the C in the model number you submitted is actually a G?

You have a new control but it still is completely dead like the old control.

What is needed to check this problem is a volt meter. If the new control is dead then I suggest voltage must be checked to the control. The wiring diagram below may be helpful to you.

Remember to unplug the range fist.

You changed the control so we'll start there. There should be a black and white wire. There should be 120 volts there as long as the range is plugged in.

This should only be done by a technician or someone who is extremely comfortable using a meter. Use caution around live voltage.

If you have no meter or don't feel comfortable checking voltage then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

I doubt two control would fail the same way. I'm suspicious of the hi-limit switch.

This should help but you can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
July 23, 2011
See more answers

Top Parts