Model #MGR6875ADW MAYTAG Free Standing, Gas

  • Control Panel/top Assembly
    3 Results
  • Oven
    3 Results
  • Body
    3 Results
  • Gas Controls
    3 Results
  • Door (upper)
    3 Results
  • Door (lower)
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
  • Wiring Information (at Series 13 & 14)
    3 Results
Find part by diagram >

Question and Answers

Q:

broiler MGR6875ADW Maytag Maytag cooking

A:

Hello, glad to help.  Thank You for choosing Sears PartsDirect.com. We, at Sears, value your service.
 
I am sorry and do understand your frustration when there is problems with the oven broiler.
 
Glad to help out.  I’m looking at your Maytag Oven model number MGR6875ADW.

It looks like you need to test out the broiler and here below is how to do so.

How to test gas igniters for ranges:

1.  Unplug the oven from the wall for your safety.

2.  Lower the oven door.  Sometimes best to have more room and just remove it.

3.  Remove the oven racks from inside.  Remove the lower panel when testing the bake igniter.

4.  Remove the burner shield by taking out the screws that secure it to igniter first.

5.  Next take out the screws that hold the igniter.  Pull the igniter away from the oven wall. Unclip the wire connector.  If the wire connector is not accessible, remove the back rear panel to the oven, or remove the bottom storage drawer to access the wire connector.

6.  Get a multi meter to the lowest setting so you can measure the Ohms of resistance.  Calibrate the meter. Refer to your meters instructions

7.  Place one of the terminals on the ovens bake igniter's terminal with one of the multi meters probes.  Then touch the other terminal with the other probe.

8.  Check the multi meter's display. If the meter does not move, displaying a resistance of any numbers on the Ohms of resistance, there is no continuity.   If no continuity then the bake igniter is bad.

 
Please "RESUBMIT ANY FURTHER QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry Jr -
Sears Technician
September 22, 2014
Q:

My oven seems to work only intermittently.

A:

I know how important it is to have a good working range in the home so that you can cook a nice home cooked meal. While you are waiting for your expert answer, I suggest you add to the thread of this question and include the full model number of your range so that the expert can provide you with a more detailed answer. I did manage to find a link that will provide you with some good tips to help you with your question. I hope my link is useful.

Read More
Joseph P. -
July 11, 2011
A:

Good link, not sure if that is the problem. It is affecting both ovens top and bottom. But thanks. Brand: MAYTAG Model Number: MGR6875ADW

Read More
nsaint -
July 11, 2011
A:

Thank you for your question and I understand your concern.

It would be hard to believe the oven control board would have an intermittent failure for both upper and lower ovens. When one or the other fails to heat I recommend looking for the red glow of the igniter. If there happens to be a low voltage supply at the time the oven was turned on the glow bar igniter may not pull enough current to cause the oven safety valve to open. I can't see unplugging and plugging it back in would help. The oven igniters can also be on the verge of being too weak to cause the oven safety valve to open when there happens to be a voltage supply drop to the range or house. The oven igniter must pull between 3.2 and 3.5 amps in order to cause the oven safety valve to open and let gas flow to the burner.

I do not believe there is a problem with the oven control board and there is no history or reported issues with the control board.

Read More
Joey S -
Sears Technician
July 12, 2011
A:

Where can I hook up a volt/ohm/amp meter to test the proper working condition?

Read More
nsaint -
July 12, 2011
A:

Nsaint: The oven glow bar igniter will have two wires connected to it. You would clamp the clamp on amp meter around one of the two wires and then turn the oven on.

Read More
Joey S -
Sears Technician
July 13, 2011
See more answers
Q:

How do I Replace the Control Panel on my Maytag Oven

A:

It is very important for you to get proper instructions on how to replace the control panel on your range so that you do not damage any other parts and also so that the wires are connected properly. While you are waiting for an expert answer, I did mange to manage to find a link that will provide you with a more information about your problem: http://www.managemylife.com/mmh/questions/161729-how-do-i-replace-the-control-panel-on-my-kenmore-range. I hope my link is useful.

Read More
Joseph P. -
June 28, 2011
A:

Thank you for your question and I understand your concern.

To access and replace the Electronic Oven Control/Clock:

  1. Disconnect power supply from the range before servicing.
  2. Remove vent deflector by removing screws located on the underside of the control panel.
  3. Remove screws securing backguard panel to backguard housing. (Screws are located on the bottom and back side of control panel.)
  4. Lift control panel up, tilt forward, and lay panel on a protected surface of the maintop for servicing.
  5. Remove screw securing mounting plate to backguard.
  6. Disconnect wiring and remove control.
  7. Reverse procedures to reassemble.

I also added an image of the control panel below.

Read More
Joey S -
Sears Technician
June 29, 2011
See more answers

Top Parts