Model #MGR6775ADB MAYTAG Free Standing, Gas

  • Control Panel/top Assembly
    3 Results
  • Oven
    3 Results
  • Body
    3 Results
  • Gas Controls
    3 Results
  • Door (upper)
    3 Results
  • Door (lower)
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
  • Wiring Information (series 13 & 14)
    3 Results
Find part by diagram >

Question and Answers

Q:

Replacing stovetop ignitor on Maytag Precision Touch 750 Range MGR6775ADB Maytag Maytag cooking

A:

I think its great that you are wanting to do some repairs on your own and I will be happy to help. I did some research and I was able to find a link that will provide you with some good information. I am also adding a second link in where you can set service to have your range repaired by a certified technician. I hope this helps as a guide with your part repairs while you wait for your expert response.

Read More
Joseph -
December 12, 2012
A:

Hi again, Sorry did you send the link (don't see one) or are you in the process of sending? THanks joe

Read More
Joseph -
December 12, 2012
A:

Thank you for your question and I understand your concern.

If the screws do not come out, I would definitely use a drop of Liquid wrench on the screws and let it sit awhile. DO NOT force the screw out or it will break. If you get broken loose, turn it back and forth many times until you feel it will thread out without breaking. Loosen it and then tighten it and and keep doing this and you will likely be able the thread the screws out without breaking it. Use caution because you do not want to break the screw or you will need to replace the burner base assembly.

Remove the burner grate and cap. Next remove the burner mounting screws and remove the burner base. This may give you enough access to disconnect and remove and replace the spark igniter electrode. NOTE: Disconnect the range from the power source before servicing.

If the main top must be taken off, see steps below.

Maintop Removal:

  1. Disconnect power before servicing.
  2. Remove surface burner control knobs by grasping knob and raising knob straight upward.
  3. Remove screws securing infinite switch bracket to maintop.
  4. Remove screws securing burner assemblies to maintop.
  5. Remove screws securing maintop to chassis. Screws are located in the front left and right corners with the upper oven door open.
  6. Remove screws securing ground strap to chassis.
  7. Raise and remove maintop from unit.
  8. Reverse procedures to reassemble.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
December 14, 2012
See more answers
Q:

Hello, I have a Maytag Gas Double Oven Range Precision Touch 750 Series Model MGR6775ADB and I'm trying to replace the upper oven ignitor.

A:

It's great to hear that you are wanting to change the ignitar on your own. I placed the owner's manual down on the bottom. I believe you will find some helpful information upon replacing the part.

Read More
celene -
November 19, 2010
A:

Thank you for your question and I understand your concern. No, you do not have to shut the gas off in order to replace the bake ignitor. Generally speaking you should not have to pull the range out in order to disconnect and re-connect the bake ignitor. There should be enough slack in the wiring to allow you to pull the ignitor wires out through the opening and disconnect it. If you are not able to pull enough slack in order to reach the quick disconnect harness connector then you will need to slide the range out to access the igniter quick disconnect.

The repair manual does not cover the procedure of accessing and replacing the oven ignitors. Note: If you have to slide the range out in order to access the ignitor connections, disconnect the power cord from the wall before doing so.

Read More
Joey S -
Sears Technician
November 20, 2010
See more answers

Top Parts