Model #MGR5875QDW MAYTAG Free Standing, Gas

  • Control Panel/top Assembly
    3 Results
  • Cabinet
    3 Results
  • Cavity
    3 Results
  • Gas Controls
    3 Results
  • Door/drawer
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

Maytag Gas Oven Model MGR5875QDW MGR5875QDW1 Maytag 30" gas range

A:

Thank you for your question and I understand your concern.

I do not have enough details in order to have a full and complete understanding of the failure. Based on your details "the controls work sometimes but then stop working intermittently!", it sounds like you may need a new electronic oven control/clock assembly providing it is getting the proper voltage.

The oven operation works like this. When the oven control is programmed and started for a bake cycle, the control board must close the bake relay in order to complete and provide 120 volts to the bake glow bar igniter. The glow bar igniter must glow red hot and it must pull enough current to open the oven gas valve. If the bake igniter is weak, it will glow but it may take the gas valve a very long time to open or the gas valve may not ever open. If you find the bake glow bar igniter glowing but the bake burner never ignites, the bake igniter is weak and will need to be replaced.

Now, if your indicating the clock/oven control will not power up or accept commands, the clock/oven control assembly will need to be replaced providing the control is getting the proper voltage supply of 120VAC.

I added an image below of the wiring diagram and schematic. The clock/oven control is powered up by the two circuits I traced in image below in Black and Green. The black is the line 1 (L1) voltage and the green represents the neutral (N) but the wire will be white in color and not green. 120VAC must be measured across the black wire on P4 connector and white wire on P2 connector. If 120 volts is measured and the control is dead, the clock/oven control will need to be replaced.

At this time I cannot provide/suggest a part number because I can't be certain of the symptoms/failure. If you diagnose the issue using the information provided, you can look up and order parts for the Maytag gas range model MGR5875QDW1 at Searspartsdirect.com

Check the things I have covered here and if I may be of further assistance as more details become available, please reply to this post. NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your Maytag gas range.

Read More
Joey S -
Sears Technician
October 22, 2013
A:

Thank you for your reply. I will check the 120VAC power to my electronic oven control/clock assembly as you recommend. The oven controls seem to work sometimes and then not work at random. For example, the other night I removed power from our stove and then re-applied power. After the power cycle all controls seemed to be working. I set the clock and then set a 10 minute cook and hold cycle at 200 degrees. This worked with no problems but shortly after the 10 minute cycle was complete I hit the cancel button to cancel the hold part of the cycle. After that It seemed like the panel buttons were non responsive when I pushed them with the exception of the Clean and the Convect Roast buttons....even the clock could not be reset or changed at that time. The model number on my gas stove is MGR5875QDW. Im not sure what the number 1 after the W means from your model description. Can you explain what the number 1 means? Can you tell me the correct part number for the electronic oven control/clock assembly for my stove.....I just want to make sure that I am ordering the correct part. Thanks in advance, Dale 252 305 5611

Read More
Dale -
October 22, 2013
A:

Dale: If the control is not loosing voltage, then I would suspect the oven control will need to be replaced. The #1 after the W at the end is a revision number. I did not know my computer added the one. That was my mistake. When ordering the oven control, the first two digits of the serial number dictates the series number. You will need to know the series number when ordering parts. I'm showing the part # for your control is part #5701M640-60 if the first two digits of the serial is a number 10 or below.

Read More
Joey S -
Sears Technician
October 22, 2013
See more answers
Q:

taking to long to convect bake or bake MGR5875QDW1 Maytag 30" gas range

A:

When it comes to the smell of something cooking in the Maytag range, and it comes out under cooked, it can be devastating. The link provided below is on a similar question which may give you an idea of what is going on with your range. Additional information may take 24-48 hours. If you decide on service, that link also is provide below.

Read More
Anna T -
January 06, 2013
A:

The type of problem that you are describing can be caused by a weak igniter on the bake burner. Here is a link for a brief video that describes the ignition process in your oven: Gas Ignition Operation . When the bake burner fails to heat in the bake mode, I suspect that the igniter is glowing but it is not heating properly. The resistance of the igniter is not decreasing to a point where it allows enough current to flow through the circuit to the safety gas valve. This is probably causing your heating problems. This type of failure is normally difficult to verify for sure. If you want to fix the range on your own, you can try replacing that bake burner igniter. Here is a direct link for that part; Ignitor for Maytag Range Model MGR5875QDW1 . Be sure that you unplug the range before accessing internal components and replace parts.

If you need more help, reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 08, 2013
See more answers
Q:

Convection mode not working in our oven Maytag # MGR5875QDW

A:

Managemylife.com is always a great resource to find the answers to just about anything. Your expert will research your question and respond within two business days but usually sooner.

Read More
Alina F. -
January 05, 2012
A:

Thank you for your question and I understand your concern. This is one of those cases where the voltage supply will need to be measured at convection fan motor. I do not recommend measuring voltage unless you have experience and feel safe and confident in doing so; otherwise I recommend calling a service technician to diagnose and repair your range. If you measure 120 volts and the fan is not running, replace the fan assembly. If voltage is not present; replace the electronic oven control part #5701M640-60 at the approximate cost of $193.30 The convection fan assembly is part #74011172 at the approximate cost of $120.00

To access and remove the fan assembly:

  1. Turn off power to unit.
  2. Open oven door or remove oven door, see "Door Removal".
  3. Remove screws securing convection fan cover to convection fan assembly.
  4. Remove screws securing convection fan assembly to rear of oven cavity.
  5. Slide convection fan assembly down and tilt forward on the top portion to allow assembly to pass through rear oven cavity.
  6. Disconnect and label wires from convection fan motor.
  7. Reverse procedure to reinstall convection fan assembly.

Oven Door Removal

WARNING To avoid risk of personal injury or property damage, do not lift oven door by the handle.

  1. Open oven door and place door hinge locking device into lock position.
  2. Place oven door in first stop position, then grasp both sides and lift up off the hinges.
  3. Reverse procedure to reinstall oven door.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 09, 2012
See more answers

Top Parts