Model #MGR5755QDB MAYTAG Free Standing, Gas

  • Control Panel/top Assembly
    3 Results
  • Cabinet
    3 Results
  • Cavity
    3 Results
  • Gas Controls
    3 Results
  • Door/drawer
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

My Maytag range will not bake. Everything else works buyt the bake, Ideas?

A:

Hello, It can be frustrating when your oven won't bake. I researched your question and found someone asked a question similar to yours. Here is what was posted by an expert, I have provided the link below. I hope this helps!

Read More
Jacqueline S -
July 18, 2010
A:

The most likely reason the bake burner does not light is because the bake ignitor has failed.

Take the bottom of the oven out and remove the baffle on top of the bake burner. Turn the oven to bake and see if the bake ignitor glows bright red. If the ignitor is glowing and the burner is not lighting the ignitor can still be bad. If the ignitor is not glowing at all the ignitor is almost certainly the problem.

Read More
Jimmy K -
Sears Technician
July 20, 2010
See more answers
Q:

Why doesn't the oven ignite in my Maytag range, model MGR5755QDB?

A:

I found the manual for your Maytag Oven in Manage My Life under the Manuals button. There are some troubleshooting suggestions that might be helpful to you. I attached the link below. I hope this helps!!!

Read More
Raquel F -
July 13, 2010
A:

Make sure that your control is not locked. This would prevent the oven from setting.

You could have a problem with the ignition circuit. When the BAKE light is blinking constantly, this normally indicates that an error code can be retrieved from the control. I provided information in the image below that shows how to retrieve error codes on this range. The error codes can only be retrieved in the diagnostic cycle using the directions in the image below. If you are able to retrieve the error code, you may be able to determine the cause of this oven failure.

If you attempt to repair the oven yourself, be sure that you follow electrical safety guidelines. Unplug the range and shut off the gas supply before accessing internal components.

If you need more help, submit additional details about the error code being displayed or indicate that you see no error codes. We will assist you further once we receive additional information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 16, 2010
See more answers
Q:

What would have failed to prevent my bake ignitor from working?

A:

The bake ignitor must glow and pull enough current/amperage in order for the oven safety valve to open. The ignitor must have 110-120 voltage supplied to it or it will not glow. If the bake ignitor is glowing, it must pull 3.2-3.6 amps in order for the gas safety valve to open. If the bake ignitor is glowing it is likely too weak to open the gas valve. Replace the bake ignitor and the gas valve will likely open and have burner ignition. Part number for the bake ignitor is 74008064. I added a link to Sears Parts Direct with the bake ignitor looked up.

To remove the Oven Door:

  1. Open oven door and place door hinge locking device into lock position.
  2. Place oven door in first stop position, then grasp both sides and lift up off the hinges.
  3. Reverse procedure to reinstall oven door.

To access the Bake Burner and Ignitor:

  1. Turn off electrical power and gas to the range.
  2. Disconnect gas and power from unit.
  3. Remove oven door and racks.
  4. Remove screws securing bottom bake cover.
  5. Raise the back of the bake burner cover and slide cover back to release the front edge of cover and lift out of oven cavity.
  6. Remove screws securing bake burner assembly to the oven chassis.
  7. Maneuver bake burner from the burner orifice and out of the slotted location.
  8. Pull forward on assembly to allow the ignitor terminal plug to pass through the back of the oven cavity.
  9. Disconnect terminal plug and remove assembly from the oven cavity.
  10. Remove screws securing ignitor to bake burner.
  11. Replace and reassemble in reverse order.

Read More
Joey S -
Sears Technician
June 05, 2009

Top Parts