Model #MER5775QAQ MAYTAG Free Standing, Electric

  • Control Panel/top Assembly
    3 Results
  • Cabinet
    3 Results
  • Cavity
    3 Results
  • Door/drawer
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

How to install the levelin leg on maytag oven MER5775QAQ

A:

Thank you for choosing Sears Parts Direct. I can certainly assist you. I did look into the model number you have provided, and I have found information to assist you.
The leveling legs are installed by turning them clockwise into the bottom of the oven base. You will need a level to determine if the oven is leveled correctly.  Block it off by putting  a 2X4 under the oven to make the installation easier. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day. 

 

Read More
Natasha12 -
Sears Technician
August 06, 2014
Q:

oven not baking or broiling

A:

Managemylife.com is a great place to find the answers to just about anything, especially on appliances. I would suggest that you provide a little more information such as the make and complete model number of your product so your expert will be able to provide you the best possible answer. Just click on reply below where you can provide the additional information.

Read More
Priscilla V -
October 12, 2011
A:

This type of failure could be caused by a voltage supply problem (if this is a wall oven). You can check the house circuit breakers or fuses for the oven. The elements will not heat if 240 volts of power is not supplied to the oven. The control will work if only one leg of 120 volts is supplied to the oven.

If this oven is in a range and the stove top burners don't heat, you could also have the voltage supply problem that is described above.

Some ovens have a high-limit thermostat or circuit breaker mounted to the outside back wall of the oven. If that component is tripped, it will prevent both elements from heating. You can shut off the house circuit breaker for the oven or (or unplug it ) and check the back outside wall for that type of high limit thermostat or circuit breaker. Some of the thermal circuit breakers have a red button that you can push to reset it. This may help you fix this oven failure.

If that thermal high-limit switch was tripped, I recommend that you closely monitor the oven. A stuck relay on the clock control board could be sticking to cause one of the elements to heat constantly.

You may need to have a service technician diagnose and repair this failure. Here is a link for the Sears Service website: Sears Home Services .

If you need more help, reply with additional details and the full model number of your oven or range. We will assist you further once we receive more information.

Read More
Lyle W -
Sears Technician
October 13, 2011
A:

my oven does not heat or broil but the warming drawer works as does the stove top.

Read More
Pat Gibbon -
December 14, 2011
A:

Hello Pat. Your details seem to indicate that you have an electric range. You could have a problem with the clock control board (or oven thermostat), a wiring failure or a tripped thermal high limit temperature switch that is causing this oven problem. I recommend that you reply with the model number of your range. Using that model number, we should be able to provide some specific troubleshooting for that oven problem.

Read More
Lyle W -
Sears Technician
December 14, 2011
A:

79094473802 is the model number. Thank you.

Read More
Pat Gibbon -
December 14, 2011
A:

Thanks for adding that model number. The wiring diagram for that range is shown in the image below with the affected circuits traced in their wire colors. I recommend that you UNPLUG the range and access the back of the control board as shown in the video link that I provided below. Check the orange and red wire connections on that control board. Look for a burned spot or signs of damage on that control board. If the wiring connections are okay and you see no apparent damage, then I recommend that you check the resistance through the bake and broil element circuits. You can check the take circuit through the yellow and orange wire (with the range still UNPLUGGED). Pull the yellow wire off of the control board when you make that resistance check. You should measure around 25 ohms of resistance (between 10 and 40 ohms). You can check the broil circuit in a similar manner through the blue and orange wires. If those circuits are good, then the clock control board (part 316462804) will need to be replaced. You can order that part from the Sears PartsDirect.com website (see 2nd link below). NOTE: You may also need to order that overlay unless you can re-use the original one as shown in that video. Be sure that you UNPLUG the range before accessing and replacing components. If you need more help, let us know.

Read More
Lyle W -
Sears Technician
December 14, 2011
A:

The plastic around the red wire connector is burned. Do we replace the control board? what part number is it and do you know how much it is?

Read More
Pat Gibbon -
December 17, 2011
A:

Hello Pat. That control board will need to be replaced according to your description. The part number for that control board is 316462804. It costs around $150. I provided a direct link to that part in the above response. That video that I provided in the above response shows how to replace that control board (with the range UNPLUGGED). You may also need the overlay (part 316419806) unless you can reuse the original one as shown in that video. The overlay costs around $8. If you need more help, reply with additional details.

Read More
Lyle W -
Sears Technician
December 19, 2011
A:

Hi I have a Maytag Electric stove top oven model #MER5775QAQ serial #18696082GE. The oven is about 7 years old but still looks great. Recently I noticed it no longer gets hot when I put on the bake function. The only time it gets hot is when I put it on broil and then I can see the inside top of the oven turn bright red. What do you think the problem is?

Read More
Anthony -
June 27, 2013
A:

Anthony: It could have a faulty bake element or a faulty electronic oven control. The bake element can be disconnected and tested with an Ohm meter for proper resistance. The Ohm resistance should measure approximately 18.6 Ohms. Be sure to disconnect the range from the power source before removing and testing the Bake element. If the bake element measures approximately 18.6 Ohms, I suspect the electronic oven control is faulty.

Read More
Joey S -
Sears Technician
June 28, 2013
See more answers
Q:

Maytag electric range Model MER5775QAQ won't self clean.

A:

I'm sorry to hear that you are having some difficulties with your Maytag Range. I did some research for you at Managemylife and found two expert answers to a similar question that may help until your expert can respond to your specific question. The links are attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices. I hope these links provided assist you.

Read More
James -
January 27, 2012
A:

You can try to reset that control board by unplugging the range for 3 minutes (or shutting off the house circuit breaker) to completely disconnect electrical power. After restoring power to the range, set the clock and see if the self clean cycle will work properly. I don't have programming information for that self clean cycle. I suspect that it will use the broil element and that the broil element and bake element will alternate in that mode. You may give the oven some time to heat up and see if the bake element ever comes on in that self clean mode. If not, then you may have a bad control board. The bake element and wiring are apparently okay since they work in other modes.

If you are sure that the control needs to be replaced, you can order that part from the Sears PartsDirect website. The part number for that clock control board is 74009222. Unplug the range before accessing internal components and replacing that control board.

If you need more help, reply with additional details.

If you get to the point where you need to have a service technician examine the range and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 28, 2012
See more answers

Top Parts