Model #MDE6200AYW MAYTAG Residential Dryer

  • Control Panel
    3 Results
  • Cabinet
    3 Results
  • Cabinet-rear
    3 Results
  • Door
    3 Results
  • Heater
    3 Results
  • Motor Drive
    3 Results
  • Tumbler
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

The dryer runs but produces no heat on cycle or setting. What is the most likely cause? 11085866400 Kenmore Elite Residential dryer

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number mde6200ayw and I recommend checking the breakers (or fuses) in your house electrical panel first. The dryer will run if only one of the 120 volt legs of 240 volt power is supplied to the dryer. If the second leg of 120 volt power is missing, then the dryer will not heat. 

 

If the outlet voltage is okay, then I recommend unplugging the dryer and checking the wiring connection on the terminal block on the back of the dryer. Check the continuity through the power cord as well. If these checks are all good, then I recommend removing the back panel of the dryer (with it still unplugged) and checking the thermal cutoff and operating thermostat in the back of the dryer. To check these, pull one wire off of the component and measure the resistance across the leads of the component. Each of these components should measure near zero ohms of resistance (closed).If the component is open (measures infinite resistance), then it will need to be replaced. Here is a link for a video that will help. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
December 01, 2014
Q:

Maytag Dryer MDE6200AYW

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dryer and I do understand your frustration. Glad to help out. I'm looking at your model number mde6200ayw and I recommend checking the breakers (or fuses) in your house electrical panel first. The dryer will run if only one of the 120 volt legs of 240 volt power is supplied to the dryer. If the second leg of 120 volt power is missing, then the dryer will not heat. 


If the breakers are okay, then I recommend checking the voltage at the outlet using the image in the diagram below. NOTE: You should only check this live outlet voltage yourself if you are completely confident in your technical ability to safely measure it using a volt/ohm meter. 

If the outlet voltage is okay, then I recommend unplugging the dryer and checking the wiring connection on the terminal block on the back of the dryer. Check the continuity through the power cord as well. If these checks are all good, then I recommend removing the back panel of the dryer (with it still unplugged) and checking the thermal cutoff and operating thermostat in the back of the dryer. To check these, pull one wire off of the component and measure the resistance across the leads of the component. Each of these components should measure near zero ohms of resistance (closed).If the component is open (measures infinite resistance), then it will need to be replaced. Here is a link for a video that will help. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
October 06, 2014
Q:

How do I find the washer model No, if it is not on the inside cover lid?

A:

Thanks for using ManageMyLife.com

I can understand the frustration of not being able to locate the model number. The model can be found in several locations. I have included an image to help you find the model number.

 

If you have further questions please let me know.
Thanks for using ManageMyLife.com

 

Read More
Desirea -
Sears Technician
August 31, 2013

Top Parts