Model #MAVT546EWW MAYTAG Residential Washers

  • Control Panel & Top
    3 Results
  • Cabinet & Front Panel
    3 Results
  • Inner - Outer Tub
    3 Results
  • Transmission
    3 Results
  • Base & Motor
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

drum won't spin and motor sounds bound up MAVT546EWW Maytag Maytag laundry

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your washer. Upon researching model MAVT546EWW; the motor may be worn. The load may be putting too much stress on it .

Thank you for choosing Sears Parts Direct. We appreciate your business. Have a great day.

Read More
Jeff Wallace Jr -
Sears Technician
August 09, 2015
Q:

Tub won't agitate MAVT546EWW Maytag Maytag laundry

A:

A follow up to the above post is that I pulled the belt off so the motor didn't have any drag on it and tried to run just a spin cycle. The experience was the same. The motor kicks on and sounds like its under considerable burden. Makes this sound for just a few seconds, then the sound, a spark and smoke. I'm thinking it's the motor at this point. Interested in other's thoughts.

Read More
Steig -
July 01, 2015
A:

Thank you for choosing SearsPartsDirect.com and being a valued member.  I can certainly understand how frustrating it can be when your washer will not agitate.

 
Unplug washer, disconnect harness at PS5 and test from wire insertion side of harness. 

 
Run winding - PS7 GY and Pin #5 YL of PS5.
Start winding - PS9 BU and PS10 RD.

1.5 ohms 
4.0 ohms without capacitor

Top Cover Removal
1. Disconnect power supply to unit.
2. Insert a plastic putty knife between the Top Cover and
Front Panel. Press the locking clip to release the Top
Cover. Repeat for both sides. Support lid with free
hand and rotate top until it comes to rest on hinge
stop.

Front Panel Removal
1. Disconnect power supply to unit.
2. Lift Top Cover, see “Top Cover Removal” procedure.
3. Remove two screws, 1 each side on Front Panel top
edge.

Agitator/Spinner/Outer Tub/Transmission Removal
1. Disconnect power supply to unit.
2. Remove Drain Pump hoses and Belt, see “Drain
Pump/Belt Removal” procedure steps 1 - 4.
Drain Pump/Belt Removal
1. Disconnect power supply to unit.
2. Remove back Cover.
3. Remove Drain Hose Clamps.
4. Remove Belt.
5. Remove three screws retaining Drain Pump


3. Lift Top Cover, see “Top Cover Removal” procedure.
4. Remove Tub Top, see “Tub Top Removal” procedure.
5. Unsnap Fabric Softener Dispenser from Agitator.
6. Remove screw located in the center of the Agitator/
Auger assembly.
7. Remove Agitator Auger from Agitator Base
8. Lift Agitator Base from Washer
9. Remove four screws retaining Spinner (Inner Tub).
10.After Spinner (Inner Tub) is removed, use Spanner
Wrench and Seal Nut tool to remove Seal Nut.
11. Remove gasket from Hub
12.Use Spanner Wrench to remove Hub
13.Remove Pressure Switch Hose from fitting on Outer
Tub.

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Natasha12 -
Sears Technician
July 05, 2015
See more answers
Q:

I own the MAVT546EWW agitating problems MAVT546EWW Maytag Maytag laundry

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
Sorry to hear of the issue you're having with the washer, I know how frustrating it is to have just completed a repair to have another one pop up behind it.
This sounds like an issue with the lid switch. If the switch is on its way out or there is an issue with the lever for the switch, it would fill and drain, but would not agitate. 
I would check the switch and lever and make sure they aren't damaged, and if so, they would need replacement. 
Hope this helps and thanks for using SearsPartsDirect.com. We appreciate your business. 

Read More
Jeff Wallace Sr -
Sears Technician
August 06, 2014

Top Parts