Model #MAV6458AWW MAYTAG Residential Washers

  • Control Panel
    3 Results
  • Top
    3 Results
  • Cabinet
    3 Results
  • Tub
    3 Results
  • Transmission
    3 Results
  • Base
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Clothes are to wet after spinning. MAV6458AWW Maytag Maytag laundry

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your washer and do understand your frustration. Glad to help out. Im looking at your model number MAV6458AWW  and here are some common checks that apply to all washers when you have this problem: 

First, check your drain hose behind the washer. Make sure that the hose is not kinked.

If your hose is draining to a standpipe behind your washer, make sure that it is not stuck way down the standpipe. It should only extend about six to eight inches down the pipe.

Also, check the height of your drain hose. Most washers cannot drain properly if the drain hose height is above 96 inches. Washers installed in basements sometimes have this problem.

Some washers will stop if the load becomes unbalanced. Also, some models stop spinning if excessive suds are detected. Observe your washer during the spin cycle for these symptoms.

Check your owner's manual for additional tips and troubleshooting specific to your model.  If you have further questions please resubmit your question for further information.
 
 
Thanks for choosing Sears PartsDirect.com.
 

Read More
Sherman_G_Wallace -
Sears Technician
March 26, 2014
A:

Just to clarify. The washer finishes the spin cycle, but the clothes are still too wet.

Read More
Matt -
March 26, 2014
See more answers
Q:

Hi . does the agitator have teeth on bottom inside.because when the washer runs the tub spins to drain but agitator does not in wash mode.hoping its not trans. MAV6458AWW Maytag Maytag laundry

A:

Thank You for contacting ManageMyLife.com

I understand your frustration when the washer doesn't agitate. Based on the information you provided, you need to replace the thrust bearing assembly. This part does have "teeth" that can wear down and cause the agitator not to work.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Thrust Bearing Kit for Model MAV6458AWW

If you have further questions please let me know.
Thanks for using ManageMyLife.com

Read More
Desirea -
Sears Technician
October 16, 2013
Q:

Mattag washer parts MAV4057AWW

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

 

Read More
Joseph P. -
August 05, 2013
A:

Thank you for using ManageMyLife.com. I can definitely understand the importance of getting the right kit for your model and making it work properly.

The biggest difference between the two kits is seal kit 21002237 does not go to your model number, it goes to a Maytag model MAV6458AWW which is newer than the model that you have. If the two washers had the same part specifications being used, the part number would be the same for the two kits. Because these part numbers differ from one another, there will be small and subtle differences and it would not be a good idea to purchase a kit because it looks similar or is cheaper. I checked Maytag's spec sheet for kit 21002237 and it does not list your model as applicable for the kit.

To get the original OEM kit, I would recommend ordering 12001598, that way you know for sure it will be a correct fit and won't have any issues. Hopefully this will help.

If you have any further questions or inquiries, please don't hesitate to ask. Thank you for using ManageMyLife.com.

 

Read More
Jeff Wallace Sr -
Sears Technician
August 05, 2013
See more answers

Top Parts