Model #M-462 TOSHIBA VCR

  • No Image Available - Wards
    3 Results
Find part by diagram >

Question and Answers

Q:

when dryer first starts I get a harsh metal to metal sound as drum turns. DHDSR46GE1WW Ge Gas dryer

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Henry -
June 06, 2013
A:

Thank you for submitting your question. I know the noise you're hearing is very disconcerning and I will be happy to assist you. You could be experiencing an issue with the drum felt and guide (WE9M30) or the drum bearing (WE1M462). Pull the dryer out so you can get to the back wall of the dryer to check the axle bearing mount in the center of the back panel. Remove the front panel and then the drum from the cabinet and examine the drum bearing (image below). If the drum bearing is in good condition, then the issue will be with the felt and guide. You should be able to see wear and tear on the felt and guide. You can order parts from our Sears Parts Direct web site. I hope this helps. Please reply back to this thread if you require further assistance. Thank you for using Manage My Life.

Read More
Tykara -
Sears Technician
June 07, 2013
A:

How do I put the dryer top back on?

Read More
Nancy -
June 19, 2015
See more answers
Q:

Dryer drum bearing for Ge Gas Dryer model #DWSR405GB0WW DWSR405GB0WW Ge Gas dryer

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your dryer. Upon researching model WE1M462; there would be a drum slide that goes with the drum bearing. Click here for diagram. The drum slide is key number 316.

Thank you for choosing Sears. We appreciate your business. Have a great day.    

Read More
Jeff Wallace Jr -
Sears Technician
January 11, 2015
Q:

GE dryer model DS4500EB0WW making squealing noise.

A:

It's great that you want to try and fix your dryer yourself. While you are waiting for an expert to respond I was able to locate some great information that could possibly assist you with your issue. I have added the link below. Hope this helps!

Read More
Yadira B -
February 10, 2013
A:

Thank you for your question and I understand your concern.

I suspect it could have a worn drum bearing based on your details. The drum has a shaft protruding out the back of the drum where it rides inside a plastic bearing. The bearing will likely need to be replaced. In order to access the bearing, the front panel  and drum will need to be taken out.  The drum bearing is part # WE1M462. The drum bearing can be ordered from SearsPartsDirect. 

I added an image below with the procedure for removing the drum.

Note: Disconnect the power cord from the power source before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

 

 

Read More
Joey S -
Sears Technician
February 11, 2013
A:

thank you. I removed the drum and the plastic drum sleeve bearing looks ok, but there was no o-ring like it shows on diagram on searspartsdirect.com. should I just put on an o-ring & lubricate and reassemble? Or do I need to remove the heater assembly to replace the bearing retainer possibly? please see attached photos. thank you for your help. Mike

Read More
Mike -
February 16, 2013
A:

Mike: The image I provided in my last replay does not pertain to your model. Your model has a drum bearing sleeve and not the type shown in the image above. Yes, to remove and replace the drum bearing sleeve, the heater housing will need to come off. This plastic bearing installed from the front and not the rear. The drum bearing sleeve is not to be lubricated either. Be sure to check the front bearings and seal where the front of the drum rides on the front bulkhead for any wear too.

Read More
Joey S -
Sears Technician
February 18, 2013
See more answers