Model #M-45 TOSHIBA VCR

  • No Image Available - Wards
    3 Results
Find part by diagram >

Question and Answers

Q:

DISHWASHER

A:

It is important to know that your dishes come clean and to know how much water it takes to get the job done. Managemylife.com is the place to go for answer to your question. If you would like additional information, please resubmit your question with the model number and more details. I have provided a link that may help while you wait for an expert answer.

Read More
Anna T -
February 28, 2012
A:

MY MODEL # IS KENMORE 665.16529000 I'D LIKE TO KNOW WHAT THE INITIAL LEVEL THE WATER HAS TO BE AT WHEN IT FILLS TO START A WASH, NOT TOTAL USAGE. THE WATER VALVE IS ACTUATED APPROX. 1M & 45S I'M NOT SURE IT'S FILLING THE CORRECT VOLUME OF WATER

Read More
MARIO -
February 28, 2012
A:

Thanks for adding that model number. The normal water level in that dishwasher is within 1/4" to just touching the bottom of that heating element. The 1 minute and 45 seconds that the fill valve is energized is correct for that model. With proper water pressure and water flow, the dishwasher should fill to the proper level in that amount of time. If that fill level is low, I recommend that you shut off the house circuit breaker for the dishwasher and the water supply. Check that water supply tube for proper flow and water pressure by disconnecting it from the dishwasher and placing the end in a container. Briefly open the cut-off valve to check the water coming from the end of that tube. If it is weak, then you will probably need to have a plumber fix that water supply problem. If the water flow is adequate, then you can check the inlet screen on that dishwasher inlet water valve for debris or deposits. If you find no problems, then you may need to replace that water valve. You can order parts from the Sears PartsDirect website.

If you need more help, reply with additional details and we will assist you further.

If you get to the point where you need to have a service technician examine and repair the dishwasher, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
February 29, 2012
A:

Thank you for your help, after troubleshooting I found that there are was not enough water going into the dishwasher. Water level was about 1 inch below the heating element, so I've gone ahead and ordered a new inlet valve. Thanks again

Read More
MARIO -
March 03, 2012
A:

Thanks for the update. Let us know if you need more assistance.

Read More
Lyle W -
Sears Technician
March 03, 2012
See more answers
Q:

mower LT1000 model # 917-272922 mower blades will no stop spinning even if i disengage the lever

A:

I know how important it is to have a good working Mower in your home so that you can keep your grass maintained. While you are waiting for an expert answer, I did manage to find a link that will provide you with some good information about what may be causing your problem.

Read More
Priscilla V -
July 06, 2011
A:

Thank you for your question.

I can understand wanting to know the why the mower blades will not stop turning even though you have the PTO lever off.

There are generally two possible causes for this to happen on your tractor mower.

One is that the clutch pivot for the belt tensioning is dry and need to be cleaned and lubricated because of the debris that can accumulate on top of the deck.

Make sure the top of the deck is clean,but do not use water on the top of the deck.

The other problem is more likely and that is the engagement cable from you PTO lever has frayed internally in the sheath and will not slide back enough to release the belt tensioning.

If the pivot tensioning works freely and the idler return spring is in place then I would change the blade clutch cable.

The part number for that cable is: 175067 and you can purchase it from: Sears Parts Direct .

I hope this will help. And if you need further help please reply and I will be glad to help you.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
July 07, 2011
A:

i have bin talking to another expert and he suggested and our conversations Wade B EXPERT engine pulley could be spreading out and allowing the belt to sit too far down into it which will cause the pulley to grab and not release I suspect the problem will be the rollers on the bottom of the brake arms. the rollers spin perfectly its the object that they are attached to i believe that, that object works it moves the belt so that it can cut the grass but when i disengage it doesn't until you turn off the key to the engine and push on it to get it back to original spot

Read More
taylo -
July 08, 2011
A:

Thank you for your update, yes it is possible that the pulley has separated but it is not real common. Did you check to see if the belt idler pulleys releases completely when you disengage the blade engagement lever. Please make sure the pivot point on the belt idler is pivoting freely. If it is not operating freely you will need to loosen the pivot bolt and lubricate the bolt and work it back and forth manually to get it working freely. Then re-tighten the bolt without causing any binding of the pivot action. Sam A.

Read More
Sam A -
Sears Technician
July 08, 2011
A:

do you have a diagram or an image of what im doing so i can see a better picher of what doing by any chance

Read More
taylo -
July 08, 2011
A:

Thank you for the update. I only have a parts breakdown picture, but I will give you the locations of the parts on the picture of the pivot area. Locate nut # 40 in the picture just below #36 idler pulley. This is located above # 143, then follow it straight down to # 55,56,54 and then the bolt comes up from the under side of the deck. Locate the return spring right next to it #148 which is suppose to pull the belt tightening system back when you release the PTO lever on the console. If this is not pivoting freely and the spring pulling the pivot back all the way it will still drive the blade. To make sure the cable for the engagement is not the problem I would suggest releasing it from the Idler pulley post by removing the hair pin clip m#45 and unhooking the cable spring from the post. Sam A.

Read More
Sam A -
Sears Technician
July 11, 2011
See more answers