Model #M130 JENN-AIR Countertop Microwave

  • Control Panel
    3 Results
  • Door
    3 Results
  • Oven Liner/body
    3 Results
  • Internal Controls
    3 Results
  • Blower Assembly
    3 Results
Find part by diagram >

Question and Answers

Q:

How much does the m130 jenn air door cost M130 Jenn-air Microwave oven and carts

A:

Thank you for contacting SearsPartsDirect.com with your question about the door for your Jenn-Air microwave. I am so sorry but a replacement door is no longer available for this model. The manufacturer no longer makes parts for it. In this case it would be time to replace the microwave. I have included the link for you to view the current model microwaves that are available.

Microwaves

I am so sorry we are not able to get you the parts to fix your microwave. I hope this helps. Thank you for choosing Sears, we appreciate your business. 

Read More
Rachel Morgan -
Sears Technician
March 14, 2014
Q:

I want to replace my existing build in 30" jenn-air oven model W130 and m130 microwave. do you know if the 30" Maytag model # MMW9730AS will fit into the openin

A:

I understand the importance of making sure your new appliance will fit properly into the opening of your current microwave. While you wait for the expert reply, I added the installation guide to the new Maytag model. Have a nice day!

Read More
Yadira B -
December 03, 2012
A:

I did not find the product dimensions and installation guides for the 30" Jenn-Air oven model W130 and microwave model M130. I see that Yadira B. posted the installation guide for the 30" Maytag Oven Combo model MMW9730AS in the above response. That installation manual provides the product dimensions and the cabinet cut-out requirements for that Maytag combo oven. I posted those dimensions in the image below. You can use that information to see whether the Maytag oven will fit in your existing cabinet. If you need more help, reply with additional details and we will assist you further.

Read More
Lyle W -
Sears Technician
December 05, 2012
See more answers
Q:

connecting rod assembly kohler engine

A:

I see your question is does the connecting rid suppose to have bearing to go between itself and the crankshaft. We have receive your question please allow 24-48 hours for an expert to answer your question. While you are waiting on an expert to answer your question. You can visit our searshomeservices.com website and set service with our SearsHomeServices.com team. I attached the link below. Hope this helps!

Read More
Dezeray S -
August 10, 2010
A:

A connecting rod bearing will depend on the rod itself. Some rods have a bearing that is obviously a bearing and others will have a "sleeve" type bearing. If you're replacing the rod, it will come with any bearings it should. I did check the parts for that engine and they do not show any bearing so whatever it has is considered to be part of the rod itself.

I'll list out a few of the common torque specs for that engine. If you're going into it you may need some or all of this.

  • Cylinder Head Fastener Torque (torque in 2 increments) ......... 20, 40.7 N·m (15, 30 ft. lb.)

  • Fan Fastener Torque ............ 9.9 N·m (88 in. lb.)
  • Flywheel Retaining Screw Torque ..................... 66.4 N·m (49 ft. lb.)

  • Oil Pump Cover Fastener Torque ......... 6.2 N·m (55 in. lb.)
  • Into new as-cast hole 4.0 N·m (35 in. lb.) Into used hole

  • Connecting Rod
  • Cap Fastener Torque (torque in increments)
  • 6 mm straight shank bolt ... 11.3 N·m (100 in. lb.)
  • 8 mm step-down bolt ... 14.7 N·m (130 in. lb.)
  • 8 mm straight shank bolt ... 22.7 N·m (200 in. lb.)

Read More
XX Wade_ -
Sears Technician
August 10, 2010
See more answers