Model #M1 SUPERWINCH Winch

  • Winch Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

Old Ice Maker SA8868 M1 .

A:

One way to see if the ice maker needs replacing is to test the motor. I am providing a link that may be helpful in troubleshooting the ice maker. An expert will respond with additional information.

Read More
Anna T -
June 24, 2012
A:

Many thanks. The water line into the ice maker is clear of ice and have a new water valve on it. The motor does not make any clicking noises when I left the arm up and down. Have power in the electrical wiring harnes that plugs into the ice maker.

Read More
john -
June 25, 2012
A:

Thank you for your question. I know it can be disappointing when the icemaker stops working. The best method to check this icemaker will be to manually place it into a cycle. Remove the front cover on the icemaker and you will see a large and small gear (see image). Turn the small gear about a 1/4 turn (ccw) to start the icemaker. If it does not cycle, the icemaker will need to be replaced. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

Read More
Scott D -
Sears Technician
June 27, 2012
A:

Hi, jopining thread becuse I'm having similar issue. When I turn CCW the rotation then takes over and completes, but at no point does it turn on the solenoid to refill the tray. I'm currently trying to see if the solenoid is bad but I think the ice maker itself has not been fully redet dale

Read More
dale -
September 03, 2012
A:

Dale, if the icemaker cycles but does not fill, listen for a humming sound, from the back of the unit, toward the end of the cycle. If you can hear this sound, it will indicate the water valve is getting energized but not opening and will probably need to be replaced. If you do not hear this sound, it could still be a valve problem but it could also be a problem with the icemaker. A good check for this will be to remove the icemaker and disconnect the wire harness and power from the unit. Now, insert a well insulated jumper between the black and yellow wires on the harness from the cabinet and reconnect the power. If water flows now, the icemaker will need to be replaced. If no water flows, the water valve will need to be replaced. I hope this will help you.

Read More
Scott D -
Sears Technician
September 04, 2012
A:

What if the icemaker cycles, fills with water, but continues to slow drip water out the bottom AND when it refills, but NEVER makes ice IN the icemaker. I can make ice manually in the freezer with trays, but the maker won't do it.

Read More
scott -
March 13, 2015
A:

I am having a similar but slightly different problem. Ice maker cycles and water valve opens but only stays on for about 2sec so doesn't fill the ice tray. Water flow looks good so I am convinced the valve doesn't stay open long enough. Does the ice maker control how long valve stays open or does valve? Will replacing ice maker solve this problem?

Read More
Ray -
March 20, 2015
A:

I have the same problem as Ray. My ice maker cycles, water valve opens but for only about 2 seconds. Anyone have any suggestions?

Read More
Brian -
August 18, 2015
A:

My ice maker works, but the bar won't come down completely and stops making ice because of that. Any suggestions? Thanks

Read More
Lenny -
September 02, 2015
A:

Hello all! I also have the model #M1 in my frigidaire. The fill arm was left up for several months after emptying ice tray for summer outing into a cooler. Yesterday, I realized it, and the tray didnt fill with any water after dropping arm back down. I pulled off the large gear after troubleshooting switches, etc, and it started flowing heavily after rotating plastic shaft that removes ice from tray when dumping. Now that I put gear back on, I am not sure how to align it, so it turns the water flow on\off at correct time, so water completely fills the tray. Right now, it only fills for a few secs, then stops, but does flow very freely. I know it is the gear positioning, kind of like a timing gear on a car. Any suggestions on how to line up to get more timing so water fills tray now? Thanks!

Read More
Mike -
December 28, 2015
See more answers
Q:

dyrer has no no heat what would be the cause. i see no heating elements on the parts diagram. 11085091401 Kenmore Residential dryer

A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.

For an electric dryer, first, there are two designated breakers in the breaker box that supply the voltage to the dryer. The dryer can run, but won't heat if one of the 2 breakers is tripped. If one of the breakers are flipped, please re-flip both breakers to see if the dryer will start heating.

There are several components wired in series between the timer and one side of the heating element that should all be closed. The heating element is shown on the bulkhead diagram and it is key number 14. (part 3387747)

Timer contact BK to BU

Thermal cut-off (thermal fuse)

Operating thermostat

High limit thermostat

Motor centrifugal switch not closing 2M to 1M. Once the motor starts to supply the L2 voltage to other side of the heating element.

NOTE: Please disconnect power to the dryer before disassembly or checking any parts.

If you need further assistance, please resubmit your question with additional details. Thanks for visiting SearsPartsDirect.com


Read More
Desirea -
Sears Technician
March 22, 2014
A:

my dryer takes a long time to dry what could cause this?

Read More
david -
November 13, 2015
See more answers
Q:

Drip pan M1BXXLZYB00 Maytag Refrigerator