Model #LXR9445JQ1 WHIRLPOOL Residential Washers

  • Top And Cabinet/literature
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket, And Tub
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous/optional
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

rinse cycle not working LXR9445JQ1 Whirlpool Washer

A:

Thank You for contacting SearsPartsDirect.com

I can understand your frustration when your washer is not working properly. If the washer makes it through the spin cycle after the washer cycle then there is only two other possibilities. 1. Try a different temperature for the rinse cyclce. If this fixes your issue then the water valve needs to be replaced.  2. The only othere problem would be the timer. The timer is what tells the machine to perform the rinse cycle. Try using the rinse cycle on other modes (example: delicate) I hope this helps troubleshoot your washer. 

If you need further assistance, 
 
Please resumbit your question with additional details. Thanks for visiting SearsPartsDirect.com
 

Read More
Desirea -
Sears Technician
December 27, 2014
Q:

my Whirlpool washer keeps stopping during the agitaion cycle LXR9445JQ1

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Joseph P. -
April 15, 2013
A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Joseph P. -
April 15, 2013
A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Joseph P. -
April 15, 2013
A:

Thank You for choosing SearsPartsDirect.com

I can understand the frustration when you washer doesn't work properly. Especially after replacing parts on the unit. Have you tried to set the washer to the spin cycle to see if the water will drain? If it doesn't work on the spin cycle then I would recommend checking the lid switch assembly. The connector may not be properly connected or the switch may have gone bad. The lid switch is a safety feature that tells the machine the lid is closed and it can continue to run the different cycles. Please feel free to respond to this post with your findings.

I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Lid Switch Assembly for Model LXR9445JQ1

Read More
Desirea -
Sears Technician
April 16, 2013
A:

Yes I did already try and put it on spin, it did not do anything. I took the lid switch apart to see if it was that and I forced the two pieces of metal together but it didn't make a difference either. Any other ideas? Could the lid switch still not work even though I took it apart and manually touched the two pieces of metal to one another?

Read More
nathan -
April 17, 2013
A:

You can bypass the lid switch to try and trouble-shoot the issue. I have included the instruction below. But keep in mind performing the bypass is for troubleshooting purposes only. Instructions 1 Remove the two Phillips-head screws from the front corners of the control panel. Pull the control panel slightly forward, and then flip it up over the back of the washer. Let the control panel hang by its hinges. 2 Locate the lid-switch connector on the top of the washer body, under the control panel. It is the only connector that goes into the top of the washer body. Squeeze the locking tab on the harness and pull it out of the connector. 3 Insert a jumper wire into the lid-switch connector that attaches to the control panel. The connector has two wires attached to it, one violet and one gray. Bridge these two wires by inserting the bare ends of a jumper wire into the connector. You can now operate the washer through a full cycle. 4 Remove the jumper wire, and connect the lid-switch harness after completing the diagnostic of the washer. 5 Flip the control panel forward, and push it slightly back to seat it against the rear panel of the washer. Install and tighten the two Phillips-head screws in the front corners of the control panel.

Read More
Desirea -
Sears Technician
April 17, 2013
See more answers
Q:

Whirlpool LXR9445JQ1 top load washer: Agitate but no spin.

A:

Wet clothes are more than just a nuisance. The expert will review what you have done so far and respond. I did locate two similar posts with information that may help with the diagnosis. I attached the links below. I hope this helps find the cause.

Read More
Barbara H. -
April 06, 2012
A:

If the motor is running in spin and the water is draining out then the problem is likely the clutch and/or basket drive. A broken clutch spring might even be the only problem. There is something you might try first. In the spin cycle after the water drains out try turning the washer off for a momnent then back on and see if the spin starts. If it does then the problem is a neutral drain problem and the timer will need to be replaced. If it turns out to be the clutch/basket drive then check the following video to see how to access the clutch: Replacing the Clutch on a Whirlpool/Kenmore Direct Drive washer . If you decide this is a repair you'd like to try any parts you need can be obtained from the following link: Whirlpool Washer model LXR9445JQ1 Parts . You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
April 07, 2012
A:

Thanks Fred. Just to be certain, if it is just a clutch problem I should be able to see the outer housing of the clutch assembly spinning, correct?

Read More
Jeff -
April 07, 2012
A:

I shut shut the washer off momentarily during spin cycle. Still a no go.

Read More
Jeff -
April 07, 2012
A:

If you give the basket a little push during spin does it turn and start spinning? If the basket will not turn at all then it may be a bearing problem. The images below may be helpful to you.

Read More
Fred M -
Sears Technician
April 09, 2012
A:

Gave the basket a push. Still a no go.

Read More
Jeff -
April 10, 2012
A:

Did the basket turn at least when you gave it a push? If it didn't turn then the problem might be a bearing or it might be a lost sock under the basket jamming things up.

Read More
Fred M -
Sears Technician
April 11, 2012
A:

I am able to turn the basket by hand.

Read More
Jeff -
April 11, 2012
A:

If the basket will turn but not spin then I suspect the clutch and/or basket drive is the problem. You will need to remove the transmission to check the clutch. You can have it repaired at your home by a Sears technician. Here is a link for the website: [Sears Home Services | http://www.searshomeservices.com?sid=MMLxexpertxmerch] .

Read More
Fred M -
Sears Technician
April 13, 2012
A:

Thanks Fred. Parts ordered. Will report back after repairs are made.

Read More
Jeff -
April 14, 2012
See more answers

Top Parts