Model #LTF2940EE0 FRIGIDAIRE Residential Washers

  • Control Panel
    3 Results
  • Cabinet/top
    3 Results
  • Motor/tub
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Error Code E-47 LTF2940EE0 Frigidaire Washer

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com.
 
I am sorry and do understand your frustration when there are error codes of E-47 on the washing machine.
 
Glad to help out.  I’m looking at your Frigidaire Washer model number LTF2940EE0.

E-47 Control board thinks  the door PTC circuit is open in spin.
check:
Remove the door lock assembly and measure the resistance of the PTC.
CORRECTION:
Shorted or open.  Defective door lock assembly.   Reads around 1500 OHMS.  Defective control board.
 
 
Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry Jr -
Sears Technician
July 31, 2014
Q:

Washer will not spin. Have checked & cleaned filter at pump, have checked pump for clogs & tested with power(works). Model is Frigidaire LTF2940ee0

A:

It is frustrating when you no longer have the convenience of your washer. I researched your question and found someone asked a similar question. Here is what was posted by an expert, I have provided the link below. I hope this helps!

Read More
Jacqueline S -
August 02, 2010
A:

On something like this the control should have displayed an error code. Most failures on this washer will trigger an error code indicating the problem or give us a direction to head into. I recommend setting the control up into a diagnostic test mode to recall the last stored error code or codes. I suspect a door lock failure, error codes E41, E47 or E48. Please see the image provided below for the test mode instructions & error code list. Remember to disconnect power before attempting any type of service.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
biker dave -
Sears Technician
August 04, 2010
A:

I have E-47 Error Code, but i can't read the chart it is blured. Could you send me a copy to my E-Mail at emathunder@atlanticbb.net so I can find out what part I need. Thank you

Read More
emathunder -
July 29, 2014
See more answers
Q:

Why won't washer spin LTF2940EE0 Frigidaire Washer

A:

Hello, glad to help.  Thank You for choosing Sears PartsDirect.com.
 
I am sorry and do understand your frustration when there is problems with the washer.
 
Glad to help out.   Im  looking at your Frigidaire Washer model number  LTF2940EE0.
 
To run a DIAGNOSTIC TEST:

->  On non-digital display models, turn the Program Knob to start position, Drain/Spin.

->  On digital display models, turn the Program Knob to start position, Touch Up. (NOTE: If the model has a timer dial that can be rotated 360°, turn the Program Knob to start position, Drain/Spin.

->  Press Pause Cancel to turn off LEDs.

->  Within 5 seconds, press and hold the Option and Pause Cancel buttons until LEDs start sequentially chasing, then release buttons.
  1. All the LEDs will sequentially light. Pressing a button below a light cluster will light all the LEDs in that cluster at one time to confirm functionality.
  2. Turn the program knob (1) click clockwise from the start position. The hot water solenoid will activate and hot water should enter through the detergent compartment.
  3. Turn the program knob (2) clicks from the start position. The bleach water solenoid will activate and cold water should enter through the bleach compartment.
  4. Turn the program knob (3) clicks from the start position. The bleach and the wash water solenoids will activate and cold water should enter through the softener compartment.
  5. Turn the program knob (4) clicks from the start position. The door lock solenoid will activate.
  6. Turn the program knob (5) clicks from the start position. The door lock solenoid will deactivate and the loading door can be opened.
  7. Turn the program knob (6) clicks from the start position. The washer will fill and tumble.
  8. Turn the program knob (7) clicks from the start position. The washer will fill and spin (leakage test).
  9. Turn the program knob (8) clicks from the start position. The drain pump and door lock solenoid will activate and the washer will operate in high spin. SAFETY WARNING: If power is removed during this test, the door can be opened. To prevent injury, DO NOT put your hands inside when the tub is rotating.
  10. Turn the program knob (9) clicks from the start position. The control will signal the last error code. 
EXITING DIAGNOSTIC MODE:

There are 2 options for exiting out of the diagnostic test mode and getting the washing machine back to normal operation:

1.  Unplug the power cord, wait 5-8 seconds, then reconnect the power cord OR

2.  Turn the program knob clockwise 2 or 3 clicks after the Start Position. Press Options and Pause Cancel buttons together for a few seconds until wash cycle LEDs appear. If a situation arises where you cannot exit the Diagnostic mode as described above and the bank of 5 LED's on the right end remain ON regardless of Program Knob position, a combination of pushed buttons may have caused the control to enter a special factory test mode. Disconnect power to reset the control to return washer to normal operation is this occurs
 
 
Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
July 17, 2014

Top Parts