Model #LSW9750PW3 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Controls And Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Water System Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Burning Smell LSW9750PW3 Whirlpool Residential washer

A:


Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
 I am sorry and do understand your frustration when there is a burnt smell in the washer.

Glad to help out.   Im  looking at your Whirlpool model number lsw9750pw3.
 
You are right in that this is a direct drive.   When the direct drive goes bad, just makes a loud noise and then breaks but no smell.   
 
It sounds at first like an electrical wire problem to be checked out.
 
Burning or electrical odors may be caused by issues with the electrical supply to your appliance.
 
To resolve this issue means:
1.  Make sure that the appliance is not plugged into an extension cord and is on its own dedicated circuit.
 
2.  Test the circuit by using another high amp draw appliance such as a heater or hair dryer.
 
a.  If the problem also occurs with the test appliance, call an electrician to resolve the power supply issue.
 
b.  If the problem only occurs with the washer, there may be a problem with the washer requiring service with a Sears Technician.  1-800-469-4663.
 
 If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
October 22, 2013
Q:

Washer just drips water ....hot or cold or both. Lsw9750pw3 Whirlpool Residential washer

A:

Thank you for contacting ManageMyLife.com regarding your Whirlpool washer. I'm happy to help you today. Based off of your description, the water inlet valve (p/n 3979346) will need to be replaced. I found a video that will help you install the valve.

Parts can be purchased at Sears PartsDirect. If you do not feel comfortable repairing this issue yourself, service can be scheduled at the following link: Sears Home Services.

I really hope this information helps you today. Thank you for using ManageMyLife.com.

Read More
Korinna S -
Sears Technician
October 15, 2013
Q:

My whirlpool ultimate care 2 LSW9750PW3 washer wont agitate, drain or rinse, makes a humming/whirring sound from the control panel. All it does is fill tub.

A:

A washer is definitely something we depend on and when it begins to malfunction it can be a huge inconvenience.  While you are waiting for an expert to respond, I have added a  helpful link that may provide information to assist you with your question.

Read More
Yadira B -
April 18, 2013
A:

Thank you for your question and I understand your concern.

Based on your symptom and details, I suspect the lid switch is not closing and completing the Neutral circuit to the motor. If the lid is open or if the lid switch is broken or not closing, the motor will not run. It will fill with water, but the motor will not operate in the agitation or in the drain and spin cycles.

The lid switch is located under the control panel on the left side of the top. When the lid is shut, the left lid hinge strikes the lid switch actuator which closes the switch and completes the Neutral circuit to the motor.

The control panel will need to be placed in the service position in order to access the lid switch. There should be a couple of screws to remove from the control panel end caps and then slide the control panel forwards and lift it up and hinge it over the rear panel.

I added an image below of the lid switch assembly and how to replace if needed. There is also a possibility that the left lid hinge arm is not striking the lid switch actuator too. You may be able to slightly bend the hinge arm enough to cause the lid switch to close.

 This may be the issue. If not, please reply and I will be glad to assist you further.


Read More
Joey S -
Sears Technician
April 19, 2013
A:

Thanks for the reply. The problem was a stuck sock in the water pump. Took it out and all is good.

Read More
tej -
April 19, 2013
A:

tej; If I knew it was humming from under the washer then I would have mentioned that the drain pump could have been jammed but I though the humming was coming from the control panel area/timer and not from the motor. I'm glad that was all it was. Thank for using Manage My Life. Have great weekend.

Read More
Joey S -
Sears Technician
April 19, 2013
A:

It was coming from the timer area, at least I thought so. Thanks for your help again. You have a great weekend too...

Read More
tej -
April 19, 2013
See more answers

Top Parts