Model #LSR8244EQ1 WHIRLPOOL Washers

  • Top & Cabinet
    3 Results
  • Controls & Rear Panel
    3 Results
  • Agitator, Basket & Tub
    3 Results
  • Brake, Clutch, Gearcase, Motor & Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Brake & Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Lint filter Whirlpool topload washer LSR8244EQ1

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your washer and I do understand your frustration. Glad to help out. I'm looking at your model number LSR8244EQ1 and here is a link for a video that will help with the repair. Once the agitator is out you will see the 4 plugs. The old ones will pop out. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

 

Read More
Sherman_G_Wallace -
Sears Technician
February 11, 2015
Q:

Whirlpool washer spin cycle doesn't work.

A:

I'm sorry to hear that you are having some difficulties with your washer . I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Barbara H. -
October 22, 2011
A:

If the washer will fill and agitate but it won't drain or spin the most likely cause is the lid switch and I suggest you check this first.

The image below will show how to raise the console and remove the cabinet to access the lid switch.

You can obtain the lid switch from the following link: Lid Switch .

Remember to unplug the washer before beginning.

Read More
Fred M -
Sears Technician
October 23, 2011
See more answers
Q:

Whirlpool washer not spinning, rinsing

A:

I'm sorry about the difficulties that you are experiencing with your Whirlpool washer . I did some research at Managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond to your specific question. I have attached the link below. If you decide to schedule service and have a qualified technician help you, I have also attached a link to searshomeservices.com. I hope these links will help until your expert can respond

Read More
James -
April 08, 2011
A:

Thanks for the link but my problem is slightly different as it agitates but will NOT rinse/spin or drain? It just stops

Read More
Sheila -
April 08, 2011
A:

Thank you for your question.

By what you have stated, it sounds like a lid switch failure. The lid switch has to be closed for the drain and spin cycle on your washer to work. If the lid switch is faulty, it will fill and wash but nothing else. A quick check you can do is to jump the lid switch and see if it will drain. If the washer operates, the lid switch needs to be replaced.

To jump the lid switch you need to unplug the washer and open the console. I have provided you with the instructions for opening the console below. Once you have the console open, locate the connector for the lid switch. Place an insulated jumper between the two colored wires. Not the green it is a ground and will cause a short. After inserting the jumper make sure it will not touch anything metal, plug the washer in. Start the washer in a drain cycle. If the washer drains and spins, you need to replace the lid switch. Do not leave the jumper in while you are waiting for the part. The jumper is only of the test.

To you replace the lid switch you have to remove the cabinet of the washer. The instructions for that are also in the image below. Once the cabinet is removed you can take the screws out securing the lid switch and remove the harness from the clips along the underside of the cabinet. Then reinstall the lid switch in the reverse order. Before you reassemble the cabinet, please read the instructions for installing the cabinet provided in the image.

Please click here to watch a video on how to replace the lid switch.

I hope this is helpful. Please reply below if you need further assistance. Here is a link to order any parts you need. Sears Parts Direct .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for using Manage my life. Mark T.

Read More
Mark T -
Sears Technician
April 10, 2011
See more answers

Top Parts