Model #LSR8233EQ0 WHIRLPOOL Residential Washers

  • Top And Cabinet
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Machine Base
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer stays stuck on a cycle such as spinning, draining water, agitating, I have to push knob in and manually move to next cycle LSR8233EQ0 Whirlpool Home washers direct-drive

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the washer.
 
Glad to help out.   Im  looking at your Whirlpool Washer model number LSR8233EQ0.

It sure sounds like you are having a timer motor switch problem being that yoiu have to manually push the knob for it to complete the cycle.   I would believe then you need a new timer.   I have it on the blue link below.

Timer for the model 
 LSR8233EQ0

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 










Read More
Larry L -
Sears Technician
May 29, 2014
Q:

probable broken fill valve LSR8233EQ0 Whirlpool Home washers direct-drive

A:

Good afternoon.... I can appreciate your wanting to do the job yourself and save $... Your theory is sound but it may also be the pressure switch. I did locate a link that will discuss this situation in greater detail. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instructions. I hope this data will enable you to address and complete the task before you and have a nice day.

Read More
Henry -
December 10, 2012
A:

Thanks for the question about your whirlpool washer and the water issue, I will be glad to assist you.
Based on the description you have provided I will say that the inlet valve does need replacing. I will attach a link for the part here: Inlet valve Your washer has only on inlet valve assembly. I have attached an image below showing how to remove cabinet so the valve can be replaced. The valve is mounted on the back panel of the washer and is accessed after removing the cabinet Always disconnect power supply before servicing the appliance and when testing live voltage be sure to wear proper safety equipment (gloves and eye protection) also be aware of sharp metals on product Be sure to turn water supply off and unplug the washer before starting any service.
I hope this helps should you need additional assistance please reply with details and I will be happy to respond.

Thanks Ron H.
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Ron H -
Sears Technician
December 11, 2012
See more answers
Q:

Whirlpool Washer: #LSR8233EQ0 - Replaced clutch to fix grinding during spin cycle..now clothes get wrapped on/under agitator at end of wash cycle & during rinse

A:

The clothes getting wrapped around the agitator can harm the clothes items and I will be happy to help. I am adding two links below to help you with your question while you wait for your expert response.

Read More
Joseph P. -
February 01, 2012
A:

still having same problem...any ideas?

Read More
Brad -
February 03, 2012
A:

Thank you for your question on the replacement of the clutch.

It sounds to me like the basket is turning while it is agitating. This will definitely wrap up the clothes around the agitator.

If you can watch it and see that is happening then the basket brake is not being engaged to hold the basket still during agitate.

Please review this video to check your installation of the clutch and brake system.

Repair Clinic clutch video .

Please let me know what you find out.

Sam A.

Read More
Sam A -
Sears Technician
February 03, 2012
A:

You know what, while I was in there I didn't replace the white brake piece b/c it looked ok, so I will go back in and replace it and give the washer another shot. I'll let you know how it goes. Thanks!

Read More
Brad -
February 03, 2012
A:

In the meantime, do you know if it matters how the two pieces I included in the pictures should be installed. Should the white plastic tip that extends up go outside of the metal wings (picture one) or in between the two wings (picture two)? Thanks!

Read More
Brad -
February 03, 2012
A:

Well, I replaced the brake piece yesterday but was still having the same problem with clothes getting wrapped around and under the agitator. Now today I was going to try a delicate load and after the water filled the Agitator would not start spinning which seems more like a coupler problem. Should have just replaced it when I was in there the first time. I guess that will be my next step.

Read More
Brad -
February 05, 2012
A:

Thank you for the update on the washer. If the agitator is not moving back and forth during the wash cycle then it could be the coupler. If the washer spins okay then it is not the problem. It could in the transmission. If the washer wraps the clothes around the agitator during the wash cycle then the basket must be rotating during the washer cycle. The brake should be holding the basket still during agitate. If not then there may be something wrong with the basket drive clutch and brake. The first picture you gave for the piece on the top of the drive block is correct. Just make sure it docks correctly onto the under side of the agitator. Please let me know what happens. Sam A.

Read More
Sam A -
Sears Technician
February 06, 2012
See more answers

Top Parts