Model #LSR6332KQ1 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Controls And Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Water System Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

whirlpool washer tub won't spin during spin cycle. Model # LSR6332KQ1 Making humming sound

A:

I'm sorry to hear that you are having some difficulties with your washer, especially when you need to keep the clothes nice and clean. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assistance for you.

Read More
Joseph P. -
December 06, 2011
A:

Thank you for your question as to why the washer will not spin.

If the lights are dimming in the house when the motor hums the transmission could be locked up or there could be something in the pump.

It is agitating? Does it pump the water out of the tub but just will not spin?

If this is the case then I would say that the drive coupling between the motor and the transmission may be broken.

If the drive coupling has never been replaced before it is my first choice for the problem.

If you feel comfortable with doing this repair your self then I can give the instructions on how to repair it.

If you decide it is the coupling here is the link for purchasing the part.

Motor coupling .

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Please let me know what you would like to do.

Sam A.

Read More
Sam A -
Sears Technician
December 08, 2011
A:

Sam A, I did go ahead and removed the motor coupler and yes it was broken. I went and purchased the new coupling today and plan to install it tonight. Hopefully this is the cause and the washer will work fine. I will let you know how it works out. Thanks for your expert advice. Dave

Read More
David -
December 08, 2011
See more answers
Q:

Why isn't my washer spinning?

A:

I do not have enough details to know if it will agitate or not. If the washer motor runs and there is no agitation action or spinning action but will drain water would indicate a broke motor coupler. The motor coupler is what connects the motor shaft to the transmission shaft. When the motor coupler breaks the washer will not agitate or spin however it will still pump out water. The motor coupler is part# 285753A, price $15.49

In order to access the motor coupler will require removing the washer cabinet.

I added three (3) images in order to reference the parts and key numbers.

To access the motor coupler the washer cabinet will need to be removed.

  • First, disconnect the power cord from the power source.

  • The console (key#26) will need to be placed in the service position by removing two (2) hidden screws, one (1) screw located at the bottom of the left hand end cap (key#7) and one (1) screw located at the bottom of the right hand end cap (key#10).

  • In order to access the two (2) screws hidden under the left hand end cap trim (key#8) and under the right hand end cap trim (key#15)the two (2) end cap trim pieces will need to be removed.

  • To remove the trim, place you finger behind the trim at the very top and bend it up enough to clear the console and then hinge it towards the front and off.

  • Remove the hidden screw under each end cap trim. Slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

  • Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) cabinet clips (key#6) off.

  • Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

  • Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

  • Remove the pump and motor by prying the retainer clips off. The motor coupler consists of three parts. One part fits on the end of the motor shaft, one on the transmission shaft and the rubber portion links the two parts together.

Reverse the procedure to re-assemble the washer.

Read More
Joey S -
Sears Technician
A:

I also have a problem with my washer not spinning. It's a Whirlpool lsr6332kq1

Read More
jason -
October 07, 2011
See more answers

Top Parts