Model #LSQ9564JQ0 WHIRLPOOL Residential Washers

  • Top And Cabinet/literature
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Machine Base
    3 Results
  • Wiring Harness
    3 Results
  • Water System
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Miscellaneous/optional
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Draining issues LSQ9564JQ0 Whirlpool Automatic washer, compact a/w

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the draining of the washer.
 
Glad to help out.   Im  looking at yourWhirlpool Washer model number LSQ9564JQ0.

First thing always is to check the drain hose.   Make sure it isn't kinked or clogged.   Check the drain pipe too.

Between the motor and the pump is a coupling.   That is the part that makes the tub spin so it can drain.

Check the lid switch.   It could be a big problem being the reason of turning off and not spinning.   CHeck with a multi meter for continuity.

Check the wiring down on the motor switch and make sure that it is connected.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
June 16, 2014
Q:

How Do I Replace The Agitator Dogs ? LSQ9564JQ0 Whirlpool Automatic washer, compact a/w

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when there is problems with the washer.
 
Glad to help out.   Im  looking at your Whirlpool model number LSQ9564JQ0 .

I see you are looking for instructions on how to replace your agitator dogs.  I hope this will help.

1.   Unplug your washer power cord and open the lid on the washer.

2.  Take off the cap from the top of the agitator by hand.  

3.  Look inside the agitator and pull up on the plastic handle that attaches to the debris cap.  Pull the debris cap completely out.  The cap has a rubber o ring around the perimeter of the cap so be careful with it.  If it comes off make sure you put it back on the cap.

4.  Remove the hex bolt just inside the center area of the agitator to the tub using a socket wrench.  It is a long area so wise to have an extension on your socket wrench so you can reach the bolt.  Lift the botttom of the agitator off of the drum and pull the agitator out of the washer.

5.  Set the agitator aside at your feet.  Twist and pull the top half of the agitator from off the bottom.  Remove the 4 agitator dogs and the washer dog cam from the top half.  

6.  Insert the new dogs into the cam.  The dogs have ears that look like a tear drop.   The cam has slots around the sides that the dog ears fit into.  Set the cam and washer dogs into the top half of the agitator.  

7.  Just repeat the process of putting everything back and shouldn't be too difficult a job.  Good luck

If you have further questions please let me know.
Thanks for choosing Sears PartsDirect.com

Read More
Larry L -
Sears Technician
February 05, 2014
Q:

How can I test if the timer on my washing machine is bad?

A:

I can understand how it maybe frustrating when your washing matinee not working correctly. I located a similar question like yours that was answered by an expert. I hope that it provides you with some more general information i wish you good luck.

Read More
celene -
October 17, 2010
A:

On this type of diagnosis you will need to use a meter in order to check voltage to the timer motor. If you are not comfortable checking voltage with a meter I recommend calling for service. After accessing the console area start the washer in a spin cycle. Place the meter on volts A/C and carefully place the meter leads across the 2 wires coming from the timer motor. If you read 120volts then you will need to replace the timer.

Timer; 3954071 $111.48 www.searspartsdirect.com?MML=MMLxexpertxmerch

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
biker dave -
Sears Technician
October 18, 2010
See more answers

Top Parts