Model #LSQ9200PQ0 WHIRLPOOL Residential Washers

  • Top And Cabinet Parts
    3 Results
  • Controls And Rear Panel Parts
    3 Results
  • Agitator, Basket And Tub Parts
    3 Results
  • Machine Base Parts
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump Parts
    3 Results
  • Wiring Harness Parts
    3 Results
  • Brake And Drive Tube Parts
    3 Results
  • Gearcase Parts
    3 Results
  • Water System Parts
    3 Results
  • Miscellaneous Parts - Optional Parts (not Included)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

My Whirlpool Ultimate Care II LSQ9200PQ0 washer wont spin or agitate and there is a buzzing sound when the spin cycle is supposed to run. What do you think?

A:

It is frustrating when your washing machine is not working properly. I have taken some time to research your question here on the Manage My Life website and I noticed that someone else had asked a similar question with a posted response from an expert I attached the link below for you to view while you wait on your expert answer. I hope the link that I provided is helpful.

Read More
Alina F. -
January 06, 2011
A:

Thank you for your question and I understand your concern. Based on your symptom and details your describing a broken motor coupler.

When the motor coupler fails, the washer will not agitate or spin but it will however pump the water out.

In order to access and replace the motor coupler, the washer cabinet, drain pump and motor will have to be taken off.

The control panel must be placed in the service position in order to remove the two cabinet clips and to disconnect the lid switch harness connector. Once the cabinet clips have been taken off and the lid switch harness connector removed from the top, the washer cabinet can be tilted forwards and walked away from the base.

I added the basic instructions on the image below. If you find a broken motor coupler, the part number needed is 285753A. You can order the motor coupler from Sears PartsDirect

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
January 08, 2011
A:

Joey- Thanks for the great information (diagrams and instructions too). Upon checking the motor coupler, it was cracked. I was able to replace it for under $20 and get the washer back up and running for the weekend laundry. Thanks again! You were a great help!

Read More
William -
January 08, 2011
A:

my whirlpool ultimate care 2 washer mod # LSQ8543JQ0 ..turns on and fills with water, but wont wash,spin or drain.when its on spin it only hummes but wont empty.would love to have your expert opinion on what might be wrong and about what it should cost to get fixed so i dont over pay.thanks for your time it is sooooo appreciated :).

Read More
daddysfavtoy -
October 23, 2012
A:

Daddyfavtoy: I must assume the motor just hums after it fills with water just as it did when in the spin cycle. If there is something jammed inside the drain pump the motor will not be able to start and run and the motor will hum. There could also be loose or disconnected wire connection at the motor or at the timer. It could also be a bad motor, timer or speed switch. The service technician will need to diagnose and provide an estimate of repair. The service fee is approximately $150.00 at which time the tech will diagnose and provide an estimate of repair.

Read More
Joey S -
Sears Technician
October 24, 2012
See more answers
Q:

Washer will fill, agitate, and pump, but will not spim.

A:

I understand that your washer is not spinning and it needs to be fixed as soon as possible. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
April 20, 2012
A:

We may need a few more details before we know what the problem is. If the washer will fill, agitate and spin then the motor and lid switch are okay. One thing to try first is to give the basket a push when it is trying to spin. If you give the basket a push and it starts to spin then you may have a weak basket drive. If the tub will not turn then the problem might be the bearing or something is under the basket jamming things up. You can also try this. Once the water has drained out try turning the washer off for a moment then back on. If the washer starts to spin then you have a neutral drain problem and the timer needs to be replaced. You can reply with any additional details for further assistance with this problem.

Read More
Fred M -
Sears Technician
April 22, 2012
See more answers
Q:

My Whirlpool LSQ9200PQ0 washer emits a strong burning rubber smell after a load of laundry.

A:

It is certainly concerning when there is a burnt smell coming from your washer. I have taken some time to research your question here on the Manage My Life website and I was able to locate a similar question to yours. I attached the link below for you to view while you are waiting on your response from an expert. I hope the link that I provided gets you one step closer to repairing your Whirlpool washer. Have a great day.

Read More
Alina F. -
July 08, 2011
A:

Thank you for your question and I understand your concern.

Your Whirlpool washer is considered a direct drive washer because it has no belt. The odor you smell is likely the rubber coupler located between the motor and the gear case. The coupler is likely getting hot due to overloading or because of repetitive wash loads and is emitting the odor. If the washer is still agitating and spinning then the motor coupler is likely Okay. When you hear the motor running and it won't agitate or spin then the motor coupler has likely broken and will need to be replaced.

I added a YouTube video showing how to access and replace the motor coupler

Read More
Joey S -
Sears Technician
July 09, 2011
A:

Thanks for your answer, Joey. I used the YouTube video to take everything apart to get to the motor coupler. Once I got there, I inspected the coupler parts for burning or wear and tear. They looked fine for being seven years old. The rubber part wasn't cracking and didn't seem melted at all. However, I noticed that a plastic cover on a connecting wire on the motor was melted and burned out. I took it off the wire (what was left of it) and replaced it with some electrical tape. I can only assume this was the problem. I put everything back together and I'm now testing it. We'll see what happens. Keep you posted.

Read More
Ryan Alford -
July 09, 2011
See more answers

Top Parts