Model #LSQ9010LW0 WHIRLPOOL Residential Washers

  • Top And Cabinet/literature
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Machine Base
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Where is the motor, front or back of my washer Mod LSQ9010LW0 LSQ9010LW0 Whirlpool Washer - direct drive

A:

Thank You for choosing Sears PartsDirect.com. I regret to hear that you are having issues with your washer and do understand your frustration. Glad to help out. Im looking at your model LSQ9010LW0   and to access the motor coupler will require removing the washer cabinet. (See images below)

 

  • First, disconnect the power cord from the power source.

 

  • The console (key#26) will need to be placed in the service position by removing two (2) hidden screws, one (1) screw located at the bottom of the left hand end cap (key#7) and one (1) screw located at the bottom of the right hand end cap (key#10).

 

  • In order to access the two (2) hidden screws, the left hand end cap trim (key#8) and the right hand end cap trim (key#11) will need to be removed.

 

  • To remove the end cap trim (key#8&11), place you finger behind the trim at the very top and bend it up enough to clear the console and then hinge it towards the front and off.

 

  • Remove the hidden screw under each end cap trim at the bottom of the end caps. Slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

 

  • Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) gold colored cabinet clips off as shown in the second image below.

 

  • Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

 

  • Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

 

  • Remove the water pump by prying the two (2) pump retainer clips off.

 

  • Leave the two (2) pump hoses connected to the pump and shove the pump over to the left and out of the way of the motor.

 

  • Disconnect the motor wire harness plug from the motor.

 

  • Pry the two (2) motor retainer clips off. Note: if there is a screw threaded through the motor retainer clips, remove the screws before prying the motor retainer clips off.

 

  • Remove the motor.

You now have access to the motor coupler. The motor coupler consists of three (3) parts. One fits on the gear case input shaft, one fits on the motor shaft and the rubber isolator links the two together once the motor is reinstalled.

See images below for further instructions.

Reverse the procedure to re-assemble the washer. If you have further questions please let me know. Thanks for choosing Sears PartsDirect.com.

http://www.managemylife.com/images/55-stored/54165/original/image56257img-or.jpg?1379489221

 

http://www.managemylife.com/images/55-stored/54166/original/image65263img-or.gif?1379489224 

Read More
Sherman_G_Wallace -
Sears Technician
November 14, 2013
Q:

On Whirlpool washer model LSQ9010LW0 how do you remove the bolt holding the agitator down? The bolt turns either left or right but only so far then no farther.

A:

I'm sorry to hear that you are having some difficulties with your washer . I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided assist you.

Read More
Joseph P. -
October 10, 2011
A:

Thank you for submitting a question to Manage My Life.

The bolt should turn counterclockwise until it comes out. Here is a video that will demonstrate removing the agitator in a washer like yours; Video . Always unplug or de-energize electrical equipment before removing covers or attempting service. Be careful and wear appropriate hand protection when working around sharp metal parts. This video is for demonstration purposes only. This washer may not look exactly like yours, but the procedure is basically the same.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details, in a reply to this post.

Landell

Read More
Landell -
Sears Technician
October 12, 2011
See more answers
Q:

What is the procedure for replacing the clutch or brake and drive tube?

A:

The clutch assembly is most likely worn causing it not spin and not the brake and drive tube. You will need to remove the washer cabinet, motor and gear case in order to access and replace the clutch. The clutch bands is designed to grip the clutch drum and as the clutch torques around the end of the clutch band strikes the clutch engagement cam which causes the brake band to release on the brake and drive tube so that it can begin spinning.

  • First, disconnect the power cord from the power source.

  • The console will need to be placed in the service position by removing two (2) screws, one (1) screw located at the bottom of the left hand end cap and one (1) screw located at the bottom of the right hand end cap. The instructions on releasing the console on the last image does NOT pertain to your model but all other information will.

  • Remove the screws at the bottom of both end caps and then slide the console forwards about 1/4 inch and the raise it upwards and hinge it over the rear panel.

  • Disconnect the 3 wire lid switch harness plug located on the top. Pop the two (2) gold colored cabinet clips off as shown in the image below.

  • Place the tip of a flat tipped screw driver down into the first valley and then push the handle end to the rear of the washer to pop off the cabinet clips.

  • Open the lid and grab the opening and tilt the top of the washer cabinet forwards just a few degrees and then walk it backwards and off.

  • Remove the water pump by prying the two (2) pump retainer clips off.

  • Leave the two (2) pump hoses connected to the pump and shove the pump over to the left and out of the way of the motor.

  • Disconnect the motor wire harness plug from the motor.

  • Pry the two (2) motor retainer clips off. Note: if there is a screw threaded through the motor retainer clips, remove the screws before prying the motor retainer clips off.

  • Remove the motor.

  • Remove the agitator by removing the cap and bolt. Lift the agitator off by grasping the bottom and not the top.

  • Remove the three gear case mounting bolts.

  • Lean the washer up against the wall and pull the gear case out. You now have access to the clutch assembly.

See images below for further instructions.

Reverse the procedure to re-assemble the washer.

Read More
Joey S -
Sears Technician
October 07, 2009

Top Parts