Model #LSB6300LW0 WHIRLPOOL Residential Washers

  • Top And Console/literature
    3 Results
  • Controls And Rear Panel
    3 Results
  • Agitator, Basket And Tub
    3 Results
  • Machine Base
    3 Results
  • Brake, Clutch, Gearcase, Motor And Pump
    3 Results
  • Wiring Harness
    3 Results
  • Brake And Drive Tube
    3 Results
  • Gearcase
    3 Results
  • Water System
    3 Results
  • Miscellaneous
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

I am trying to replace the dogs on my whirlpool clothes washer. I cannot separate the top part of the agitator from the bottom part.

A:

I am sorry that you are having some difficulties with your repairs and I will be happy to help. I did some research and I was able to find a link that will guide you with your project. I hope this helps with your research while you wait for your expert response.

Read More
Joseph P. -
January 26, 2013
A:

The fabric softener dispenser should remove without to much trouble. Beneath the dispenser is a cap that is removed next. Beneath the cap should be a cam and bolt. If there is a bolt then remove the bolt and then remove the agitator. I you see no bolt then you should see a plastic cam. Q 1/2 inch drive for a socket can be used to push down and turn the cam to release it. A pair of needle nose pliers can be used as well. The image below may be helpful to you. You can reply with any additional details for further assistance.

Read More
Fred M -
Sears Technician
January 27, 2013
A:

If the image above does not enlarge then please try the image below.

Read More
Fred M -
Sears Technician
January 27, 2013
A:

the top part of the agitator seems not to be connected to the bottom part , it does not spin with the bottom part.

Read More
marty -
February 26, 2015
See more answers
Q:

washer doesn't fully drain LSB6300LW0 Whirlpool Washer - direct drive

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com
 
I am sorry and do understand your frustration when the washer won't fully drain.
 
Glad to help out.   Im  looking at your Whirlpool Washer model number LSB6300LW0.

Make sure the door is closed firmly.

If the washer is not spinning and draining, the lid switch should be the first item checked.

Check the drain hose to make sure it isn't kinked, or blocked.

Check the spout where the drain hose sends the water to make sure it isn't clogged.

Clean the hose and pump area to make sure there is no foreign objects.

Could be the pump starting to go bad.

Please "RESUBMIT YOUR QUESTIONS IF THERE IS ANY OTHER PROBLEMS".
 
Thank you for your understanding in this matter and I hope we can help you with your future questions and repairs.  Thank you for choosing Sears and using our SearsPartsDirect.com.
 

Read More
Larry L -
Sears Technician
July 09, 2014
Q:

my whirlpool washing machine is not getting water to the tub, do you have any ideas as to the problem

A:

A dry wash doesn't really work for the laundry. Sounds like you have used available troubleshooting and made a repair. It can be disappointing when that fails to resolve the problem. The expert will be reviewing this model and what has been done. In the meantime I did locate another similar post with an expert answer that may help. I attached the link below.

Read More
Barbara H. -
January 27, 2011
A:

Your symptoms seem to indicate that the washer begins to agitate immediately when it should be filling. This type of problem is often caused by a failed water level pressure switch in the console. I provided the wiring diagram for this washer in the first image below. The second image shows the fill circuit for the rinse cycle traced in purple and pink (wire colors connected to the pressure switch). If the washer is agitating when it should be filling, then it is possible that the contact in the pressure switch V to T (traced by the red line) is stuck. This completes the path to the tan wire and would cause the washer to agitate without filling because it detects that the tub is already full. Replacing the pressure switch will normally fix this problem. I provided a parts diagram in the third image that shows the pressure switch as Key 12. It is part number 3366847. You can order this pressure switch from the Sears PartsDirect website. Here is a direct link to that part that shows a picture of it: Water level switch . Unplug the washer before accessing internal components. You can open the console by removing the screws on the back of the each console endcap (Key 49 in the parts image). You can then flip the console up into the service position as shown in the 4th image. If you have a volt/ohm meter, you can check the continuity between the V and T contact (with the washer still unplugged ). If you measure near zero ohms of resistance (continuity) between these contacts when the washer is empty then this verifies that the pressure switch will need to be replaced.

This information should help you resolve this washer problem. If you need more assistance, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 28, 2011
See more answers

Top Parts