Model #LRG30357ST LG Free Standing, Gas

  • Burner Box
    3 Results
  • Stove Top
    3 Results
  • Oven Cavity
    3 Results
  • Door & Drawer
    3 Results
  • Orifice Diagram
    3 Results
Find part by diagram >

Question and Answers

Q:

Is there a difference between natural and lp gas orifices? LRG30357ST Lg Gas range

A:

Thank you for your question and I understand your concern with your LG gas range.
 
The LP gas orifices' for the surface burners must be removed and the NAT gas orifices installed. The range comes from the factory set up for Natural gas and the LP orifice spuds are supplied with the range. The LP orifice's is located at the back of the warming drawer compartment. If the previous owner or service technician put the NAT gas orifices back where the LP orifices were stored, you may find the NAT gas orifices'. The spuds/orifices are in a metal bracket next to the pressure regulator and are attached to the back wall of the compartment by a ¼-in. hex head screw. An LP conversion instruction sheet is also located in this area.
 
I hope this helpful. If you furhter assistance, reply to this thread.
 

Read More
Joey S -
Sears Technician
February 11, 2014
A:

Thank you for your question and I understand your concern with your LG gas range.
 
The LP gas orifices' for the surface burners must be removed and the NAT gas orifices installed. The range comes from the factory set up for Natural gas and the LP orifice spuds are supplied with the range. The LP orifice's is located at the back of the warming drawer compartment. If the previous owner or service technician put the NAT gas orifices back where the LP orifices were stored, you may find the NAT gas orifices'. The spuds/orifices are in a metal bracket next to the pressure regulator and are attached to the back wall of the compartment by a ¼-in. hex head screw. An LP conversion instruction sheet is also located in this area and you can reverse the procedure to convert it back to Natural gas.
 
I hope this helpful. If you need further assistance, reply to this thread.
 

Read More
Joey S -
Sears Technician
February 11, 2014
See more answers
Q:

How do I replace the plastic part on the knobs of my LG Gas Range (LRG30357ST)?

A:

Having plastic pieces that keep breaking in the middle of stainless steel knobs would be a bit frustrating. The expert will review available resources for another option. One option might be to unscrew the cap and remove the plastic piece to take to the local hardware store to see if they have something that may work.

Read More
Barbara H. -
May 10, 2012
A:

Thank you for your question and I understand your concern.

The knob is not a repairable item. The knobs would have to be replaced.

If the knobs are hard to turn after pushing it in; the gas valves will likely need to be replaced. I can't think of any other reason why the knobs would keep breaking.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Read More
Joey S -
Sears Technician
May 12, 2012
A:

HI Barbara, I know of a custom solid aluminum knob supplier vs.the cheap plastic knobs from LG. Let me know if you are interested. Regards,

Read More
LGKNOBGOD -
August 08, 2012
A:

Can you please guide me from where I can get this solid aluminum knob? I am in Canada.

Read More
Altaf -
November 13, 2012
A:

I have a $1.50 per knob solution: 1. Buy a 1/2 x 5/8 x 1 spacer at Lowe's ($1.50 each - get 5 pieces) 2. Clean knobs, remove back cover of knob and connect broken plastic parts with glue (liquid form). Make sure little metal inside the plastic is on front end. 3. Apply glue (gel form) around plastic then slide the metal spacer over. Add more gel glue to fill up space between plastic and metal. Might want to wait 30minutes then apply more glue if there is still space or gap. That's it! I recommend waiting 24 hours to let glue cure until putting it back on range. Now you can put cap back on but would need to make the whole a little wider using a grinder.I used a small flathead screwdriver and a hammer and just chip off small pieces until metal sleeve would fit. However, I think u can do without the cap if you have strong glue. My pics are not best quality but it looks much nicer after I cleaned it up and removed excess glue. Feel free to contact me for questions: cbraza@yahoo.com My wife is very happy, saved her a lot of money coz new ones cost as much as buying a new range itself!

Read More
carlo -
January 24, 2013
A:

Hey Joey S "EXPERT", how about they are cheaply made? if just one person forgets or does not know you have to push it in to turn it, it is damaged beyond repair. Don't play ignorant, it was designed that way, TO BREAK, otherwise why are replacements so horribly expensive. I WILL NEVER BUY LG PRODUCTS AGAIN!!! They probably cost the manufacturer 10 cents to make.

Read More
Brian -
July 17, 2013
A:

LG Burner knobs are a joke. I got a one year additional warranty and made them replace it twice in that year. I think we should have a class action suit. The replacement knobs over 3 years cost more than the burner. I will never buy LG equipment ever again.

Read More
Vaseem -
October 06, 2013
See more answers
Q:

Oven does not start LRG30357ST Lg Gas range

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
James -
May 11, 2013
A:

Thank You for choosing SearsPartsDirect.com

I can understand how frustrating it can be when you oven stops working. Based on the information you have provided, I would recommend check the temperature sensor. This sensor tells the ignitor when to turn on and off. I have included a link to our PartsDirect page where you can purchase the part you need to complete your repair. Just click the blue link below to be taken to the page.

Temperature Sensor for Model LRG30357ST

Read More
Desirea -
Sears Technician
May 12, 2013
A:

Thank you very much Desirea - I have already ordered a new oven temperature sensor. One question: how does one check it? The contacts seem OK at the multimeter, so the problem is in the piece (that looks like a pencil) itself, not in the wiring. Best Flavio

Read More
Flavio -
May 12, 2013
A:

I would recommend checking the contacts on the control board where the temperature wiring harness connects to the board.

Read More
Desirea -
Sears Technician
May 14, 2013
See more answers

Top Parts