Model #LEQ6000ES2 FRIGIDAIRE Residential Dryer

  • Cabinet/drum
    3 Results
  • Front Panel/lint Filter
    3 Results
  • Controls/top Panel
    3 Results
  • Motor
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Frigidaire Affinity Error codes E5B,E9E and E4A

A:

Anyone?

Read More
David -
November 06, 2011
A:

Hi David,

Thank you for submitting a question to Manage My Life.

Without your model number I am only able to give you general information.

E5B= Heater Fault (no heating). Position cycle selector to NORMAL, temperature selector to HIGH HEAT and touch START. Measure the voltage across terminals on relay RL2 (heater relay) on electronic control. If meter reads 240V on electric models and 120V on gas models, replace electronic control. If meter reads zero, remove power from dryer. Disconnect wire going to NO terminal on the relay RL2. Reconnect power and measure voltage drop between terminal COM on relay RL2 and neutral. If meter reads zero, wire between incoming line and relay RL2 is open. If meter reads 120V, check the rest of the heater circuit.

E4A = Program Time out Fault. Press PAUSE CANCEL and SELECT buttons for 6 seconds to exit test modes. Position cycle selector to NORMAL, temperature selector to HIGH HEAT and touch START. Check for anything that would extend dry times such as: no heat, restricted vent, blower fan blade broken or loose, dryer installed in closet with solid door, or bad connection in moisture sensor bar circuit or dirty bars. If dryer operates normally but code returns, replace electronic control.

E9E Code = Low Voltage seen at the Control. Make sure to check the RED wire on the Control Board that connects to the Heat Relay. This is L1 to the Control Board and we have seen bad/loose connections and burnt wires at the terminal causing this issue.

You will most likely need to replace the main control, but without your model I am hesitant to tell you to do that.

If you would like specific help with your dryer, please reply to this post with the model number and more details.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Here is a link that you may use to view the parts list diagram and for parts purchases; Sears Parts Direct .

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.

Landell

Read More
Landell -
Sears Technician
November 07, 2011
A:

The model is AEQ6000ES2. After following all the flow charts, I noticed that one common sense "No heat" test was missing. Ohm the heater element. The element was open. I just finished replacing it and all is well.

Read More
David -
November 07, 2011
A:

Hi David, Glad to hear you are up and running! Please keep Manage My Life in mind for all of your do-it-yourself projects. Landell

Read More
Landell -
Sears Technician
November 08, 2011
A:

I am having the same problem. I do not know where to locate the heater relay RL2 or even the electronic control

Read More
IFEDI -
November 13, 2011
A:

I just did the troubleshoot as directed but I am having a 120V meter reading which says check other heater circuits. I have checked for loose connections but no headway. Any suggestions, I don't want to pay more to have a tech come over. Will really appreciate anyone's help.

Read More
IFEDI -
November 13, 2011
A:

Hi Ifedi, Without your model number I am only able to give you general information. The control board is in the console and the relays are on the control. If you would like specific help with your dryer, please include the model number and more details in a reply to this post, and I will be happy to assist you further. Landell

Read More
Landell -
Sears Technician
November 14, 2011
A:

Landell, the model number for the frigidaire dryer is GCEQ2152ES0. I have done the troubleshooting up to the point of voltage drop and I am measuring 120V. At this point, the manual says check other heater circuits and I do not know how to go about it from here. Will appreciate your help. Thank you.

Read More
IFEDI -
November 14, 2011
A:

Hi Ifedi, Since you are not giving me many details, I will assume you are getting the E5B error code. The model number you gave me is an electric dryer. If you read 120vac across the heater relay in a normal dry cycle, you will need to ohm the heating element, and the high limit thermostat. You should have resistance from one terminal to the other on the heating element and each terminal to the housing should read open. You should read resistance across the high limit thermostat as well. If either the heater or the high limit are bad they will need to be replaced. I am giving you the disassembly instructions in the images below. These images are for demonstration purposes only. This dryer may not look exactly like yours, but the procedure is basically the same. I hope this is helpful. Check the things I have covered here, and if I may be of further assistance, include more details in a reply to this post. Landell

Read More
Landell -
Sears Technician
November 15, 2011
A:

I have a co-worker that has an Frigidare Affinity model# AEQ6000ES2. Its giving code E4A and not heating up, she was told by a tech is was a bad card. Would that be a control board or the interface board? She has told me that it has over heated in the past, not sure how she knows this, now there is no heat. So will a new control board fix her problem? Thanks.

Read More
Tony -
February 24, 2012
See more answers

Top Parts