Model #LEQ2152ES0 FRIGIDAIRE Residential Dryer

  • Cabinet/drum
    3 Results
  • Front Panel/lint Filter
    3 Results
  • Controls/top Panel
    3 Results
  • Motor
    3 Results
  • Wiring Diagram
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Frigidaire leq2152es0 dryer keeps getting drawstrings on clothes stuck between drum and cabinet.

A:

I know that it can be very inconvenient for you to have the clothes getting stuck on your dryer. While you are waiting for an expert to respond I was able to locate some information that could possibly assist you with your issue. I have added the link below. Hope this helps!

Read More
Yadira B -
November 04, 2012
A:

Hi,

Thank you for your question, and I would like to answer the question this way.
The best is to replace the felt seals but the other best way is to use a garment bag for things with draw strings in them. Here is the link, Dryer Laundry Bag .

I hope this is helpful. If I may be of further assistance please include more details in a reply to this entry below.
Thank you for using Manage My Life.

Read More
Bill__W -
Sears Technician
November 05, 2012
See more answers
Q:

Frigidaire Dryer tearing my clothes

A:

I'm sorry to hear your having this problem with your dryer. I did some research on the issue but I couldn't find a solution for the lint trap. Your expert will research your question and respond within two business days but usually sooner.

Read More
Yadira B -
August 30, 2012
A:

Thank you for choosing MangeMyLife to assist you with this issue. This is not a common occurrence. I would first make sure there are no sharp objects in the drum itself. Be careful when doing this second inspection. Whatever is tearing the clothes could cut you. The front & rear bearings may be the cause of this problem and may need to be replaced. If the rear bearing fails, this will cause the front seal/glides to have a gap that could catch & tear your clothes. I would also replace the rear bearing & front drum felt and drum glides. If there are no loose screws or baffles then the felt seal and drum glides could cause this problem. Large loads can cause the seals to compress and leave a gap for the clothes and items such as buttons and zippers to get caught in. This may cause the lint filter to catch because the drum is not turning correctly anymore. I have provided an image below to assist you on how to perform an inspection of your dryer including the lint trap.

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact your local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

If you decide that this is a repair that a technician should handle, you can Click here to schedule service at the Sears Home Services web site.

If you have more questions, continue this existing thread, just log back into the ManageMyLife. Go to the homepage,and your profile. This will direct you to your profile page. Scroll down to the bottom of your profile page until you see "(your name) conversations" Click on your question. you'll see "Join this conversation" from there, you can reply back, then Click "reply" This is the fastest way to talk to me.

Read More
James -
Sears Technician
August 31, 2012
See more answers
Q:

dryer turns on and rotates but wont heat up!

A:

The dryer not heating can be an inconvenience and a waste of electricity. I did some research and I was able to find a link with a similar question. I hope this helps while you wait for your expert response.

Read More
Joseph P. -
May 26, 2012
A:

On this model the fuse is called a "thermal limiter" but if the dryer is running then the fuse is okay. On this dryer the heating ciecuit consist of the control relay, high limit thermostat, element and motor switch. The element and thermostat can ge checked for resistance/continuity if a meter is available. The control rely and motor switch would be more difficult to check. First check the circuit breakers. It's possible that one can trip leaving the dryer 120 volts to run the motor but not have 240 volts to heat with. To access the hi-limit thermostat you will need to remove the top panel. The image below will help you with this. Remember to unplug the dryer first.

Read More
Fred M -
Sears Technician
May 26, 2012
See more answers

Top Parts