Model #LDG8704AAE MAYTAG Residential Dryer

  • Control Panel
    3 Results
  • Cabinet-front
    3 Results
  • Door
    3 Results
  • Cabinet-rear
    3 Results
  • Tumbler
    3 Results
  • Gas Valve
    3 Results
  • Motor Drive
    3 Results
  • Ducting
    3 Results
  • Wiring Information-ldg8704aa*
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

dryer not drying LDG8704AAE

A:

Thank You for contacting SearsPartsDirect.com. I do apologize for the delay in answering your question.

There could be one of several possible component failures preventing your dryer from heating.

Timer

Hi-limit

Thermal cut-off 

Operating thermostat 

Thermal fuse 

Flame sensor

Solenoid coils

Motor centrifugal switch

In order to diagnose the failure will require disconnecting the power cord from the power source and removing the rear panel.

The hi-limit, thermal cut-off, operating thermostat and thermal fuse can be access and checked from the rear of the dryer. The failure is most likely one of the four components list above with key numbers beside them. Each one of these four components listed above with key numbers will need to be disconnected and then checked for continuity using an ohm meter. Which ever component ohms open (no continuity) will need to be replaced. I added three images to reference below. One is the wiring diagram, the basic gas dryer circuit and one showing the parts location.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website:


Sears Home Services

If you need further assistance please respond below. Thanks for visiting SearsPartsDirect.com

Read More
Desirea -
Sears Technician
April 01, 2014
Q:

gas dryer

A:

I know that it can be very inconvenient for you not to have your dryer working properly. While your waiting for a detailed reply from an expert. I have provided the link below. Good luck on the repair.

Read More
Yadira B -
October 22, 2012
A:

Thanks for the question about you dryer not heating at times, I will be glad to assist with this problem.
Based on your description of the problem I think that your dryer is working okay and the problem is in your venting system hooked to the dryer. try this simple test; remove the vent hose from the back of the dryer and run a normal load(more than one of you want to) if the dryer does a good job drying in the normal amount of time then the vent is blocked and needs cleaning.
You should also check the dryer filter closely to be sure it has not accumulated a film over the screen that will reduce air flow through the clothes while drying. I hope these tips help, if not please reply with added details and I will be happy to respond.

Thanks Ron H.
If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Ron H -
Sears Technician
October 23, 2012
See more answers
Q:

Maytag Dryer Model #LDG8704AAE

A:

I'm sorry about the difficulties that you are experiencing with your Maytag dryer. I did some research at managemylife.com and found an expert answer to a similar question that may assist you until your expert can respond. I have attached the link below. This is a different model, but it still may give you an idea of the scope of work involved to perform the repair until your expert can respond. If you would like to schedule service and have a qualified technician help you, I have also attached a link to searshomeservices.com. I hope these links will help until your expert can respond.

Read More
James -
March 22, 2011
A:

Thank you for your question.

I can understand asking what all you would need to accomplish a good repair of the dryer.

I would suggest that you should replace the two glides supports and the front drum seal and then while you have the drum out, check the rear drum support roller to make sure they are in good shape.

I would add the 314820 front felt seal. This seal uses a high temperature contact cement to attach it to the from bulk head panel.

The part number for the adhesive is: 5308027429.

You should not need any special tools.

You will need a scraper to remove the felt seal if you decide to replace it.

Or if you want to get it locally at an appliance part store you can get the Maytag adhesive 55980.

I hope this will help with repairing your dryer.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
March 23, 2011
See more answers

Top Parts