Model #LDG7304AAM MAYTAG Residential Dryer

  • Control Panel (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Control Panel (ldg7304aam & Ldg7304abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Cabinet-front (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Cabinet-front (ldg7304aam & Ldg7304abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Door (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Door (ldg7304aam & Ldg7304abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Cabinet-rear (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Cabinet-rear (ldg7304aam & Ldg7304abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Tumbler (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Tumbler (ldg7804aam & Ldg7804abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Gas Valve (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Gas Valve (ldg7304aam & Ldg7304abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Motor Drive (ldg7304aae) (ldg7304aal) (ldg7304abe) (ldg7304abl)
    3 Results
  • Motor Drive (ldg7304aam & Ldg7304abm) (ldg7304aam) (ldg7304abm)
    3 Results
  • Ducting (ldg7304aam) (ldg7304abm)
    3 Results
  • Wiring Information (ldg7304aam) (ldg7304abm)
    3 Results
Find part by diagram >

Error Codes

Error Code:



Question and Answers


Maytag gas dryer is running but not heating.


Having your dryer fail to heat can be a real headache. I did some research and provided a link to a similar question and answer on our site. I hope this will give you a better idea on the next step to take until the Expert responds to your question in more detail within 24 to 48 hours.

Read More
Julio -
June 01, 2013

Thank you for your question and I understand your concern.

There could be of many possible component failures preventing your Maytag gas dryer from heating:



  1. Timer
  2. Temperature switch
  3. Cycling thermostat
  4. High limit thermostat
  5. Radiant sensor
  6. Glow bar igniter
  7. Solenoid coils


In order for the burner to ignite, the glow bar igniter must receive 120 volts from the timer. The circuit is the routed to the temperature switch, operating t-stat, hi-limit t-stat and then to the radiant sensor and igniter.

The thermostats, radiant sensor, glow bar igniter should be disconnected and each one tested with an Ohm meter for continuity. The front panel will have to be taken off to access the components. There are a couple of screws along the bottom of the front panel. Disconnect the power cord and then remove the screws along the bottom of the front panel. Tilt the bottom outwards and then slide the front panel down. You will need to disconnect the door switch before you can remove the front panel and set it aside. The radiant sensor and high limit thermostat is mounted on the side of the gas burner cone. The operating thermostat is located on the front of the blower wheel cover.  

You can view and order parts for Maytag model LDG7304AAM at Searspartsdirect.  

 If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services.

Read More
Joey S -
Sears Technician
June 05, 2013
See more answers

Top Parts

Recommended maintenance parts & accessories