Model #LAT7304AAE MAYTAG Washers

  • Control Panel (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl)
    3 Results
  • Control Panel (lat7304aam & Abm) (lat7304aam) (lat7304abm)
    3 Results
  • Top (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl) (lat7304aam)
    3 Results
  • Top (lat7304aam & Abm) (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl) (lat7304aam)
    3 Results
  • Cabinet (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl)
    3 Results
  • Cabinet (lat7304aam & Abm) (lat7304aam) (lat7304abm)
    3 Results
  • Tub (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl)
    3 Results
  • Tub (lat7304aam & Abm) (lat7304aam) (lat7304abm)
    3 Results
  • Transmission (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl)
    3 Results
  • Transmission (lat7304aam & Abm) (lat7304aam) (lat7304abm)
    3 Results
  • Base (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl)
    3 Results
  • Base (lat7304aam & Abm) (lat7304aam) (lat7304abm)
    3 Results
  • Clutch, Brake & Belts (lat7304aae) (lat7304aal) (lat7304abe) (lat7304abl)
    3 Results
  • Clutch, Brake & Belts (lat7304aam & Abm) (lat7304aam) (lat7304abm)
    3 Results
  • Wiring Information (lat7304aam) (lat7304abm)
    3 Results
Find part by diagram >

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Washer not agitating or spinning out LAT7304AAE

A:

It can be very aggravating when your washer malfunctions and will not agitate or spin. While you are waiting for your expert answer, I did some research on the unit. At this time, I was unable to locate information that would be helpful in regards to your question. Some of these questions that are asked will need specific research and will be answered by an expert with-in two business days but usually sooner.

Read More
Julio -
November 29, 2012
A:

Thank you for your question and I understand your concern.

The most likely failure is a faulty lid switch or the lid switch is not closing and completing the voltage path to the motor.

The red and black wires on the lid switch must make internally in the lid switch or the motor will not run. There is also a check switch wired in series with the lid switch. If the check switch and lid switch do not open and close at the correct time, it will also cause the fuse to blow and the it will no longer fill with water. I suggest calling a service technician with the experience and knowledge to repair your washer.

The lid switch is located under the control panel. If you plan on checking or replacing the switch, disconnect the power cord from the power source before accessing the lid switch. I recommend calling a service technician to diagnose and repair your washer.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
December 01, 2012
See more answers

Top Parts