Model #KUDS01IJWH0 KITCHENAID Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm And Strainer Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

how to replace upper spinner part in dishwasher

A:

When it comes to replacing parts owners manuals are important to have. ManageMyLfe.com is a great place to find your owner's manual and installation guides for appliances. I did some research and found the owner’s manual. I have attached the link. Your expert will follow up and verify this information shortly. Have a get day!

Read More
Dezeray S -
June 19, 2013
A:

I know that it can be very frustrating to have issues with your dishwasher. Normally, to install the new 3rd level spinner, release the manifold from the mounting clip at the top of the tub. Pull the manifold down just enough to insert the locking pin/axle down through the manifold and into the new spinner. Push the manifold back up into the mounting clip to secure the manifold up in position. The image below may give you an idea of how the spinner is mounted. If you don't feel comfortable doing any of this yourself, just click on this link to schedule service: Sears Home Services. I hope this helps. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 19, 2013
A:

Spary arm image

Read More
AnneJ -
Sears Technician
June 19, 2013
See more answers
Q:

KitchenAid dishwasher problems

A:

Good afternoon.... I can understand your concern and you've done a good job at trying to get to the bottom of this problem. I did locate a link that will discuss this situation in greater detail. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might wrong with your dishwasher and have a nice day.

Read More
Henry -
December 18, 2012
A:

Intermittent problems can be difficult to pin down. From the description you give I believe you have two problems, the door switch and console/interface. The door switch could be bypassed to check if it is the problem. You would need a couple of small pieces of insulated wire to do this. I can tell you more about how to do this if you are interested. The middle of the cycle problem sounds like the console has a stuck or shorted keypad. You should be able to select various cycles and options all the timer and not "most of the time." The console would cost about $140 dollars and can be a do-it-yourself project if you feel comfortable with such projects. The image below will show how to remove the console. Let me know if you will to know more about bypassing the door switch.

Read More
Fred M -
Sears Technician
December 19, 2012
A:

The door switch was replaced recently, however the console has three of the six plastic screw anchors broken off. I have thought of the possibility that these broken anchors are causing some of my problem with the door switch but, it doesn't explain why or how it changes cycle options midstream. When I spoke to the phone technician on this, she suggested the electronic control board may also be bad, adding an additional $130 to my bill. How likely is it that this is also my problem. If both things are bad, with shipping, I will be spending a little over $300 on a dishwasher I can buy new for a little over $500. I DON'T want to go the wrong way on this and cost more in the end than it was all worth!

Read More
Lowell -
December 20, 2012
A:

From the description I suspect only the console is the problem. I suspect the console has a stuck or shorted keypad and that is what is causing the problem. Since the machine will run sometimes I suspect the relays on the main control that power the water, circulation and drain motors are okay. It is difficult to be certain but I believe the console is all you need to resolve this problem.

Read More
Fred M -
Sears Technician
December 23, 2012
A:

Thank you so much for your expert advise. I will be ordering that part soon.

Read More
Lowell -
December 25, 2012
A:

Good luck. One thing to try first is to remove the ribbon connector and then reinsert it and hope a better connection fixes the problem. It would also be good practice for replacing the control.

Read More
Fred M -
Sears Technician
December 26, 2012
See more answers

Top Parts