Model #KUDS01IJBL0 KITCHENAID Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm And Strainer Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

kitchenaid dishwasher blinking lights KUDS01IJBL0

A:

Thank You for choosing Sears PartsDirect.com and being a valued member. It is unfortunate to hear that you are having issues with your dishwasher and I do understand your frustration. Glad to help out. I'm looking at your model number kuds01ijbl0 and I suggest testing the door switch item 12 and verify that it is working properly. If the switches are ok you may have a defective panel or a failing keypad. Here is a link that will help with troubleshooting the door switch. I recommend having a service technician properly diagnose the problem if you do not feel comfortable testing the unit. Just click the blue link above to be taken to the page. I trust this information will help you.

 

Thank you for choosing Sears PartsDirect.com.

 

SAFETY NOTICE: Be sure to disconnect power to the appliance before performing any repairs. If you are not comfortable with doing any voltage checks that might be recommended, please contact Sears for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others.

Read More
Sherman_G_Wallace -
Sears Technician
December 12, 2014
Q:

kitchenaid kuds01ijbl0 not working KUDS01IJBL0

A:

Good morning... I can fully understand your concern regarding this issue. You've done a good job at trying to get to the bottom of this problem. I did locate a link that will discuss this situation in greater detail. Keep in mind that an expert will be responding within the next two business days if not sooner and will likely offer you more information and instruction. I hope this link will help guide you as to what might wrong with your dishwasher and have a nice day

Read More
Henry -
December 30, 2012
A:

What is the "Dual Dig Dis" and what does it do? The name is not very discriptive!

Read More
Trent -
December 30, 2012
A:

If all the lights on the console went out at once I suspect the thermal fuse or the main control board. Usually when the console breaks only one or two of the lights/keypad don't work. If all went bad at once then I suspect the main control. The thermal fuse is the usual suspect so check it twice just to be sure. One thing to try first is to access the main control in the console and remove the ribbon then re-insert it and hope for a better connection. The first image below shows the matrix for the keypads. It is difficult but with a meter each keypad can be checked. The thermal fuse can be bypassed with a small piece of insulated wire, sorry not paper clips, joining the two wires on the thermal fuse. I hope this helps. You can reply with any additional details for further assistance. The door switches have nothing to do with the console lights. You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
December 31, 2012
See more answers
Q:

Why is only the bottom rack getting clean in my KitchenAid Superba dishwasher model KUDS01IJBL0?

A:

Check the upper spray arm for cracks or splits. Make sure that the upper rack is pushed all of the way in before starting a cycle so that the manifold will dock properly to provide spray to the upper arm.

You could have debris stuck in the chopper blade area of the sump or a problem with the drain check valve that is causing your dishwasher to not clean well. I provided an image below that shows how to access this area of the dishwasher sump. Your dishwasher will look slightly different but the basic procedure is the same. Access the chopper blade area and check for a foreign object or debris that could be clogging the sump area. Check the drain check valve to make sure that it is operating properly. This will likely solve your problem.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician
September 08, 2009

Top Parts