Model #KUDP01FLBL2 KITCHENAID Dishwasher

  • Door And Panel Parts
    3 Results
  • Control Panel Parts
    3 Results
  • Door And Latch Parts
    3 Results
  • Lower Washarm And Strainer Parts
    3 Results
  • Heater Parts
    3 Results
  • Fill And Overfill Parts
    3 Results
  • Tub And Frame Parts
    3 Results
  • Pump And Motor Parts
    3 Results
  • Upper Rack And Track Parts
    3 Results
  • Lower Rack Parts
    3 Results
  • Upper Wash And Rinse Parts
    3 Results
  • Miscellaneous Parts Optional Parts (not Included)
    3 Results
Find part by diagram >

Troubleshooting

Error Codes

Error Code:

Condition:

Check/Repair:

Question and Answers

Q:

Kitchenaid Dishwasher will not start

A:

Dishwashers are the best appliance to have in a home because it washes the dishes for you. While you are waiting on an expert to answer your question, a suggestion I have is to set service with a Sears technician. I have attached the link below. Have a nice day!

Read More
Dezeray S -
September 28, 2011
A:

If the unit won't start and all of the lights are on then have you checked the door switches?

With all of the parts you've changed I thought you rated a wiring diagram to help with this problem. The 2nd image contains information on how to check the keypad switches and shows the circuit for each function.

The 3rd image contains the instructions to enter and run a diagnostic test.

If everything worked for a couple of weeks then there may just be a loose connection.

Make sure the "control lock" feature is not turned on.

I hope this helps. Remember to turn the power off before accessing any parts.

You can reply with any additional details or questions for further assistance.

Read More
Fred M -
Sears Technician
October 01, 2011
See more answers
Q:

KitchenAid KUDP01FLBL2 - 3 LED lights not working.

A:

I'm sorry to hear that you are having some difficulties with your KichenAid Dishwasher. I did some research for you at Managemylife.com and found an expert answer to a similar question that may help until your expert can respond to your specific question. The link is attached below. The expert who will assist you, can walk you through a repair like this or let you know if this may be something a technician should perform. He can also verify parts that may be required for you to order. If you do decide to schedule service and have a qualified technician help you, I have also attached a link to Searshomeservices.com. I hope these links provided will assist you.

Read More
James -
September 14, 2011
A:

Thanks for the link. That doesn't get me to my answer, as I already replaced the console that the expert refers to and there are still 3 LED lights that are not working.

Read More
Shawn -
September 14, 2011
A:

I provided some technical information that should help you with that failure in the image below. I recommend that you start that diagnostic test program as shown in the image below. In the first segment of that test, all of the LED's should turn on and then go off. If those 3 LED's that you are describing in your details do not work in that test program then I recommend that you check those circuits using the information on that left side of that image. Be sure that you shut off the house circuit breaker for the dishwasher before accessing internal components in that console. You will need a volt/ohm meter with precision probes (needle probes) to accurately test those switches and that ribbon cable. There is a chance that the ribbon cable is bad. You should be able to determine that by using the information shown below. If that cable is bad, you order a new ribbon cable from the Sears PartsDirect website. The part number for the ribbon cable is 8524447. If the user interface and ribbon cable pass the test shown below, then you will need to replace that control board (part 8564542).

NOTE: You could skip the above tests and replace both the control board and the ribbon cable. The control board costs about $100 and the ribbon cable costs around $30. Replacing both of those components should fix your problem since you already replaced the user interface and control panel. Those first 2 components that you are replaced should be okay.

If you need more help, reply with additional details and we will assist you further.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Lyle W -
Sears Technician
September 16, 2011
A:

Great answers from the experts ... the ribbon cable was the problem .... I ordered it from Sears Direct and had it in two days ... what a service this is!

Read More
Shawn -
September 22, 2011
A:

Thanks for letting us know what you found. We are glad to hear that you fixed the problem.

Read More
Lyle W -
Sears Technician
September 22, 2011
See more answers

Top Parts