Model #KSCS25INSS00 KITCHENAID Side-by-Side Refrigerator

  • Cabinet Parts
    3 Results
  • Refrigerator Liner Parts
    3 Results
  • Refrigerator Shelf Parts
    3 Results
  • Freezer Liner Parts
    3 Results
  • Motor And Ice Container Parts
    3 Results
  • Refrigerator Door Parts
    3 Results
  • Freezer Door Parts
    3 Results
  • Dispenser Front Parts
    3 Results
  • Air Flow Parts
    3 Results
  • Control Parts
    3 Results
  • Unit Parts
    3 Results
  • Icemaker Parts, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

KSCS25INSS00 beeping and not cooling KSCS25INSS00 Kitchenaid Counter depth sxs refrigerator

A:

I sorry to hear about the problems that you're having with your refrigerator. I'll try to help you.

The refrigerator main control board has some diagnostics that may help you determine the cause of your problem. Here's an image that show the main control board diagnostics: KitchenAid Refrigerator Main Control Board Diagnostics.

I recommend that you allow the test program to check the thermistors (temperature sensors). Make sure that the fans run and try to start the compressor. If the compressor doesn't start, you can carefully check the LED on the inverter control board. Here's an image that shows the codes that the LED may blink on the inverter control board: KitchenAid Inverter Board Diagnostics.

Check the part numbers for the control boards that you installed in the refrigerator. The main control board should be part 2307028. The original inverter control board (box) substitutes to new part number W10133449. Unless the inverter box was previously replaced, that part W10133449 may have needed some wiring revisions to properly install it so that it works with the control board part 2307028. If you have any questions about the parts, let us know.

I hope that this information helps. If you need further assistance, let us know.

Thanks for choosing Sears PartsDirect.

 

Read More
Lyle W -
Sears Technician
April 21, 2015
A:

Dear Lyle, I am having the same issue. However I am having a hard time running the Main Control Board diagnostics. When I press the C and on/off button, both FC and RC say "1". Your instructions says it should say "O1" on the FC to start. Also, I have a hard time finding the invertor board blinking light. Do I have to remove any covering in order to see the light? Thanks for your help>

Read More
Paul -
April 25, 2015
See more answers
Q:

The ice maker will make a few batches of ice then start dripping and freezing into a block. KSCS25INSS00 Kitchenaid Counter depth sxs refrigerator

A:

Thank you for choosing Sears Parts Direct. I will be happy to help with your refrigerator. Upon researching model KSCS25INSS00; make sure the icemaker is level. If its level then it could be that the water valve is not closing properly.

Thank you for choosing Sears. We appreciate your business. Have a great day.    

Read More
Jeff Wallace Jr -
Sears Technician
January 27, 2015
Q:

Ice maker doesn't make ice. KSCS25INSS00 Kitchenaid Counter depth sxs refrigerator

A:

Searspartsdirect.com is always a great resource to find the answers to your parts questions. Your Sears partsdirect expert will research your question and respond within two business days but usually sooner. Thank you for using Searspartsdirect.com!

Read More
Julio -
April 02, 2013
A:

 

I know that it can be very frustrating to have issues with your ice maker. The icemaker in this model can stop working for a few reasons. Some are listed below:

  • The icemaker itself can fail
  • The water valve may not open
  • The optic boards can fail
  • The fill tube can freeze up
  • Freezer temperature not cold enough (should be 0 to 5 degrees)

The blinking led light can be flashing a code that will indicate the problem. If it flashes 2 times pauses and continues this while the door is open, it will be normal and if it stays on continuous, when the flapper door on the left side is held in, it indicates the boards are ok. When checking this icemaker, tape the little flapper door shut and disconnect power to the refrigerator. To check this icemaker, slide it out, so the front cover can be removed, to access some test terminals. There is a clip located on the back right corner of the icemaker that will need to be removed, to slide the icemaker out. There will be a screw at the bottom of the clip holding it. I'm sending a picture with instructions to remove this clip. With the clip removed, slide the icemaker out and remove the front cover. You will now see the test terminals, which are marked (see picture). Now remove the 3 screws holding the receiver board on the right side pull the board out and disconnect the harness from the board. Place a jumper between the black and black/white wires (see picture). Now use a second jumper and place it between the L - V terminals on the module. Reconnect the power and with both jumpers in place, water should now flow to the icemaker (be prepared to catch water from the fill tube). If water does flow, the icemaker # 2198597 will need to be replaced. If no water flows but you can hear a humming noise, the water valve # W10247725 will need to be replaced. If nothing at all happens, some voltage checks will need to be made. I hope this will help you. If you would like more assistance, reply to this thread and I will be glad to assist you further.

If you do not feel confident repairing this problem or doing any voltage checks yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services . If you need more assistance additional details will be helpful.

Safety Notice: Be sure to disconnect the appliance before performing any troubleshooting procedures. If you are not comfortable with doing any voltage checks or repairs that might be recommended, please contact a local service provider for repairs. Be aware that there could be sharp edges inside the appliance that could cause cuts or other injuries to yourself or others. If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
April 03, 2013
A:

Images for testing

Read More
AnneJ -
Sears Technician
April 03, 2013
A:

how can i get the pictures you mention in this thread?

Read More
M -
January 05, 2014
A:

also please send the voltage tests you mention that need to occur after these previous tests have been completed Thank you! Marty

Read More
M -
January 05, 2014
A:

I was wondering if you could send me the link for the pictures above. Also any information on the voltage and ohms would be greatly appreciated.

Read More
Rick -
July 30, 2014
A:

what causes the fill tube to freeze up? it froze up and then water began leaking as it kept trying to fill the ice maker.

Read More
Victor -
December 03, 2014
A:

Would also like the test pictures that are shown here

Read More
Victor -
December 03, 2014
See more answers

Top Parts