Model #KGST307HWH9 KITCHENAID Slide-In Range, Gas

  • Cooktop/literature
    3 Results
  • Cooktop Burner
    3 Results
  • Control Panel
    3 Results
  • Door And Drawer
    3 Results
  • Oven Chassis
    3 Results
  • Broiler And Oven Burner
    3 Results
  • Oven
    3 Results
  • Rear Chassis
    3 Results
Find part by diagram >

Question and Answers

Q:

Kitchen Aid model; # KGST307HWH9 has error code E1:F2, how do i know if it is the touch pad or the oven control board? i think i could replce either part mysel

A:

Thank you for your question and I understand your concern.

The F2/E1 fault code implies the "Cancel" key pad is not working. I recommend disconnecting the range from the power source for a few minutes and then power the range back up and see how it operates.

According to the tech sheet, it says to clean the surface of the glass control panel. Also, if the control panel flat ribbon connector is not making a good connection to the electronic range control, it could cause the same fault code.

I added a couple of images below with the procedure of removing the control panel and control board. NOTE: Disconnect the range from the power source before servicing.

I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
September 13, 2013
Q:

Why spark module model W10110491 is not working in my KitchenAid model KGST307HWH9 stove?

A:

I understand that your Kitchen-aid burners are not igniting. While you are waiting for an expert to respond, I have attached some helpful links below that may provide information to assist you with your question. Have a great day!

Read More
Alina F. -
March 08, 2012
A:

I verified that the part W10110491 is the correct replacement part for that original spark module. I recommend that you check the wire harness connections. You may need to replace that burner switch/wire harness that is part number 9755451. That part has all of the burner switches and the wiring harness from the burner switches to the spark module. That may fix the problem that you are describing. You can order that wiring harness with the burner switches from the Sears PartsDirect website. Here is a direct link for that part: Wire Harness with Switches . Be sure that you unplug the range before accessing and replacing internal components. If you need more help, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 10, 2012
A:

Lyle, I just received parts today and unfortunately the harness with switches did not worked. I also replaced base and electrode of that burner due to excessive rust that prevented me from replacing electrode - ceramic was broken. Actually as I said before, I have a spark in that burner but is going around toward base of the electrode and not toward cap of the burner. That is why I thought that spark module is not direct replacement. The discharge distance is the same or even shorter. Did I assemble something incorrectly in the burner area? I was trying to find prints of this stove assembly but only I can find is a part list. Thank you again for your help. Henry

Read More
Henry -
March 15, 2012
A:

Hello Henry. I do not have prints for that stove assembly. I do have images for the igniter and the burner assembly for a similar model that appears to have the same components. I added that image below this response. That information may help you check that igniter electrode and the alignment. That burner cab will need to be in place when you test that burner. Are you only having problems with that 1 burner?

Read More
Lyle W -
Sears Technician
March 16, 2012
See more answers
Q:

How do I remove the front glass panel of a KitchenAid 30" gas range for cleaning?

A:

To remove the front glass, follow these steps:

  • Open the door to its first stop.
  • Grasp the sides of the door and lift it up slightly. Pull the door forward until the hinge hangers are partially out of the slots in the chassis. Don't completely remove the hinge hangers from the slots because there will be spring tension on them.
  • Reposition the angle of the door to its vertical position in order to remove the spring tension on the hinge hangers. Pull the hangers the rest of the way out of the chassis slots.
  • Position the oven door on a work surface padded with towels with the decorative glass and door handle facing up. The bottom edge of the door needs to be facing you at the front.
  • Remove the four decorative glass retainer screws on the very bottom of the oven door. Remove the retainer and the two side trims.
  • You should now be able to lift the front glass off of the door. Clean it and replace it.
  • Reposition the side trims and the bottom retainer. Replace the screws in the bottom of the door.
  • To install the door back on the oven, grasp the sides of the door and insert the hinge hangers into the hinge slots and then lift the door slightly and push in at the bottom until the hangers are fully installed in the chassis. NOTE: If the hinge hangers are not seated properly, the door will not close tightly and may be off-center. To seat the hinge hangers, keep the door vertical, then lift it slightly and push in on the bottom until the hangers are fully seated.
This procedure is usually completed by an experienced technician. It is risky to attempt this process yourself. If you are not able to properly remove and reseat the oven door properly, you may need to call a service technician to help you.

If you need more help, resubmit your question with additional details.

Read More
Lyle W -
Sears Technician

Top Parts