Model #KGRT607HBS9 KITCHENAID Free Standing, Gas

  • Cooktop/literature
    3 Results
  • Cooktop Burner
    3 Results
  • Control Panel
    3 Results
  • Door And Drawer
    3 Results
  • Oven Chassis
    3 Results
  • Broiler And Oven Burner
    3 Results
  • Oven
    3 Results
  • Rear Chassis
    3 Results
Find part by diagram >

Question and Answers

Q:

my oven works but the led windows do not show anything kgrt607hbs9

A:

Thanks for the inquiry and for using SearsPartsDirect.com.
I am sorry to hear of the lack of display with the control panel, I know how frustrating that can be to have occur.
This could be caused a by a few different things. It could be as simple as a loose or unsecured wire connection to the connector from the electronic board to the control panel. It could also be caused by a defective LED function on the electronic board or possibly an issue with the panel. To properly identify the issue, the panel will need to be disassembled so the wiring can be checked and the components can be tested with a multimeter to isolate the defective part. 
In situations such as this, Sears would recommend to have a service technician help assist with the diagnosis and troubleshooting to make sure the correct part is identified. If you would feel more confident have a Sears Home Service technician help assist with the diagnosis/repair, you can call 1-800-349-5071, or click here to be directed to the page to set up service.
Hope this helps and thanks for using SearsPartsDirect.com. 

Read More
Jeff Wallace Sr -
Sears Technician
April 07, 2014
Q:

My oven won't heat up

A:

Having this happen to an appliance we count on a daily base is disappointing. I have done some research on the Manage My Life website and have located a link similar to your issue. While you are waiting for a detailed reply from an expert I have provided the link below. Hope this helps!

Read More
Priscilla V -
July 30, 2012
A:

I recommend that you check to see if the broil burner will ignite and heat properly. If it does, then I recommend that you let the oven cool off and then remove the bottom panel of the oven to observe the bake burner igniter when the oven is set in the bake mode. See if that bake igniter glows when the oven is set in the bake mode. Here is a video that shows how the oven ignition system works on that range. If the igniter is glowing but the bake burner will not light, then you may have a weak igniter. You can shut off the house circuit breaker for the range or unplug the range and switch the bake and broil igniters in that situation. The image below shows the procedure for removing the bake and broil igniters. If you switch those igniters and the bake burner lights properly, then replacing that bad igniter will fix your problem.

You can order that igniter from this page: Igniter for KitchenAid Gas Range Model KGRT607HBS9 . Be sure that you shut off the house circuit breaker for the range or unplug it before accessing and replacing internal components.

If the bake igniter is not glowing at all, then you could have a bad igniter or you could have a cooktop bimetal switch that is tripped and did not reset. The wiring diagram for this range is shown in the second image below. The circuit through that bake burner igniter is traced in red. You may need to check that cooktop bimetal thermostat. The third image shows the physical location of that component and how to access it. You can check that fuse for continuity with a volt/ohm meter. The 4th image shows how to test that bimetal thermostat. Here is a video that shows how to test that bi-metal thermostat. If it is bad, then it will need to be replaced. You can order that part from this page: Cooktop Thermostat for KitchenAid Gas Range Model KGRT607HBS9 .

If that thermostat is okay, then you can check the continuity through the igniter (or switch the bake and broil igniters as described above).

A wiring failure, a bad safety gas valve or a bad control board could also prevent the igniter from glowing.

These tips should help you diagnose and repair this failure in your range. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
July 31, 2012
A:

Here is the 4th image.

Read More
Lyle W -
Sears Technician
July 31, 2012
See more answers
Q:

Can you help me find the LP orifice for my oven so I can convert the range from natural gas to LP?

A:



I am afraid I don't understand what you want. Do you need help locating the orifices in the range, or do you need part numbers for a LP orifice? Your oven has a bake orifice and a broil orifice in it. Do you need both?

Oven orifices normally just adjust for LP or natural without replacing the orifices. If you tighten the orifice down until it is snug, it should be adjusted for LP. This would hold true for both bake and broil orifices.

There are no LP orifices offered for the oven burners, you should be able to adjust them. If you are not comfortable doing this conversion, contact the LP company and get a technician to assist you. I am sure you know LP is much more dangerous than natural gas.

Read More
expert -
Sears Technician
February 27, 2008

Top Parts