Model #KERC507HWH3 KITCHENAID Free Standing, Electric

  • Cooktop/literature
    3 Results
  • Control Panel
    3 Results
  • Door And Drawer
    3 Results
  • Oven Chassis
    3 Results
  • Oven
    3 Results
  • Rear Chassis
    3 Results
  • Hidden Bake
    3 Results
Find part by diagram >

Question and Answers

Q:

oven will not work KERC507HWH3

A:

Thank you for choosing SearsPartsDirect.com. I will be more than happy to assist you. I can understand any frustration you may have experienced with regards to your unit. Also thank you for submitting your question to our forum. I apologize that you have not received any replies. I hope you have found an answer to your inquiry. If not, please resubmit your question and one of our experts will respond for you. Again, thank you for choosing SearsPartsDirect.com.

Read More
Samantha A -
Sears Technician
November 18, 2014
Q:

Repair Manual

A:

When replacing any part on an appliance it helps to have step by step instructions. The expert will review this model and respond with those instructions. If you would like to view a similar question for a general overview, I attached a link below. I hope this information helps.

Read More
Barbara H. -
April 26, 2012
A:

I did not find a service manual for that model of range. The owner's manual shows how to remove that oven door. I provided that procedure in the first image below. Pull the oven door off and lay it on a padded surface. NOTE: That oven door is heavy. Two people may be needed to safely lift that oven door off and position it on a padded surface.

The second image below shows the parts diagram for that oven door. You can use that parts diagram as a guide for taking apart that door and replacing the glass.

These tips should help you complete that repair. If you need more assistance, reply with additional details.

If you are not confident that you can properly replace that glass on your own, then you can schedule a service technician to replace the glass. Here is a link for the Sears Service website: Sears Home Services .

Read More
Lyle W -
Sears Technician
April 27, 2012
See more answers
Q:

oven elements

A:

Having a range oven that is not heating properly can be an inconvenience and I know how fun it can be to make some baked goods. While you are waiting for an expert answer, I did manage to find two links that will provide you with some good tips about what to check on your oven. I hope my links are useful.

Read More
Joseph P. -
April 26, 2011
A:

Thank you for your question.

I can understand you wanting to know if the bake and the convection elements are working.

Ranges with the hidden bake elements will take up to 25 minutes to pre-heat.

First the convection element will not get red because the fan is right behind it and it will dissipates the heat off the element quickly. And some of the convection elements operate on 120 volts instead of 220 so those will never get red.

On your range in the bake cycle the bake and the outer broil coil is active in the bake pre-heat mode.

So you will see part of the broil element red during that selection.

First REMOVE POWER TO THE RANGE.

In order to check the hidden bake element you will have to pull the range out and remove the right side panel and then remove a cover for the element.

To remove the right side panel locate and remove the two screws at the back side of the panel and hinge the panel out to about 30 degrees and then pull back to remove.

Use a multi-meter set to the lowest ohm scale to check the element for continuity. Remove one of the electrical terminals on the element and check the element for resistance of about 25 ohms.

If the element does not show resistance it is open and will have to be replaced.

I hope these instructions will help you with your pre-heat problem.

Thank you for using Manage MY Life.

Read More
Sam A -
Sears Technician
April 27, 2011
See more answers

Top Parts