Model #JJW9530DDP JENN-AIR Built-In Oven, Electric

  • Body
    3 Results
  • Oven
    3 Results
  • Supplemental Information
    3 Results
  • Control Panel & Internal Controls (pro)
    3 Results
  • Wiring Information
    3 Results
  • Wiring Informaton
    3 Results
  • Door (pro)
    3 Results
  • Wiring Information (at Series 19)
    3 Results
  • Wiring Information (at Series 19 Frc)
    3 Results
Find part by diagram >

Question and Answers

Q:

Error Code 1d11 JJW9530DDP Jenn-air Jenn air cooking

A:

Thank you for your question. I know fault codes can create concern.  The 1d11 indicates a runaway temperature with the door unlocked. This can mean a primary failure in the control circuit of the upper oven. The result is all cooking functions are shut off. You can try a hard power reset by unplugging or shutting off the breaker to the oven, then restoring power.  If the error repeats, a technician will need to check the control circuits and probably replace the control.  You can schedule a Sears technician at Sears Home Services. If further assistance is needed, please reply.  Thank you for using Manage My Life.

Read More
Barbara H. -
Sears Technician
September 06, 2013
Q:

After a power outage, my Jenn Aire Wall Oven model JJW9530DDP went dead.

A:

Having this happen to our appliance can ruin anyone's day. While you are waiting on an expert to answer your question, I suggest you set service with a Sears technician. I have attached the link below. Hope this helps!

Read More
Dezeray -
December 10, 2012
A:

Thank you for your question and I understand your concern.

The first step in diagnosing the failure is measuring and confirming if the oven is getting the proper voltage supply of 220-240 volts. You said you reset the breaker and I must assume it was a double breaker dedicated for the oven. If the oven is getting the proper voltage of 220-240, the 110-120 voltage supply to the electronic oven control will need to be measured and confirmed across L1 (line one) and Neutral where it comes into the control board at P1 connector. If 110-120 is measured, the electronic oven control/clock assembly will need to be replaced. NOTE: I do not recommend making any voltage measurements unless you have experience and feel safe and confident in doing so; otherwise I strongly suggest calling a service technician to diagnose and repair your oven.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
December 11, 2012
A:

can you supply wiring diagram? It is a double breaker. How is the control panel removed? I took out two screws at bottom, but still seems tight. do control knobs need to be removed, in order for panel to come out?

Read More
Randy -
December 11, 2012
A:

Also, the light doesnt work, does the same 110 v supply run thru it also?

Read More
Randy -
December 11, 2012
A:

Randy: The oven light also operates off L1. I do not have access to the service manual and it appears by the image it may have two screws on each side of the control panel but the oven will likelyneed to be slid out some to access the 2 screws on each side. The knobs will also likely need to come off. I recommend calling a service technician to diagnose and repair your oven. I added an image below of the wiring diagram.

Read More
Joey S -
Sears Technician
December 13, 2012
A:

Thanks for the info. The upper panel doesnt come out separately, so had to pull whole oven. Also surprisingly, there is no fuse between wall and oven. power goes right to panel from the block.

Read More
Randy -
December 13, 2012
See more answers

Top Parts