Model #JGS8850BDS JENN-AIR Slide-In Range, Gas

  • Oven/base
    3 Results
  • Control Panel/top Assembly
    3 Results
  • Gas Controls
    3 Results
  • Body
    3 Results
  • Door (ser Pre 10)
    3 Results
  • Door (ser Pre 11)
    3 Results
  • Warming Drawer
    3 Results
  • Supplemental Information
    3 Results
  • Wiring Information
    3 Results
Find part by diagram >

Question and Answers

Q:

Vent cover installation JGS8850BDS Jenn-air Jennair cooking

A:

Thank you for choosing Searspartsdirect.com and being a valued member. I can certainly assist you in locating the instructions to replace the vent cover on your range. 

Looking at the picture of the vent cover it looks to me like the vent cover slides out. There are slots in the vent cover that allow the cover to be pushed out. You will need to inspect the cover in order to determine which way you need to push. If that does not work then you may have to get a service technician to remove. 

You can also visit searpartsdirect.com for parts, diagrams, and repair information.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Thank you for your question. Have a great day.

Please resubmit your question if you have any other problems. 

Read More
Natasha12 -
Sears Technician
September 29, 2014
Q:

Oven in Jenn-Air range stopped working with no error codes.

A:

I understand how important it is for you to have a range that is working properly so that you can make a great meal. While you are waiting for an expert answer, I did manage to find a link that will provide you with more information about your problem. I hope my link is useful.

Read More
Joseph P. -
November 24, 2010
A:

Thank you for your question.

I am sorry that your range is not working. It certainly is inconvenient to be with out your oven.

You are probably correct in thinking it is a control board. You did the right thing in resetting the power to get the microprocessor to reset.

I have given you a set of instructions for getting the control into the diagnostic mode to help you with your checking of the control.

I hope this will help.

Thank you for using Manage My Life.

Read More
Sam A -
Sears Technician
November 26, 2010
A:

Thanks Joseph and Sam for your answers. When your range isn't working, nothing like going skiing for a few days to avoid the problem. Now that I'm back, I was able to verify that the oven sensor has the correct resistance. That was about all I was able to do. I am unable to try the "Quick Test" mode because there is no response from the Setup key. I have ordered the control board. If that doesn't fix the problem, I assume the only other thing it could be is the keypad. My interpretation of the parts breakdowns I see on the web is that in order to replace the keypad, I must order and replace the entire front panel, i.e. the keypad itself is manufactured right into the front panel and cannot be replaced separately. Is that correct?

Read More
Jeff_R922 -
November 29, 2010
A:

Just to close the loop on this - I replaced the control board and got exactly the same behavior that was in my original post, so the control board was not the problem. I ordered the keypad (entire front panel, really) and that did fix the problem. So if you have the exact symptoms I described, you may want to try and replace the keypad first!

Read More
Jeff_R922 -
December 15, 2010
A:

Thank you for the update. Usually a stuck key pad will make the unit through an error code, and I am surprised that this did not. I am glad that you got it repaired . Thank you for using Manage My Life. Sam A.

Read More
Sam A -
Sears Technician
December 16, 2010
See more answers

Top Parts