Model #JGD8430ADS JENN-AIR Counter Unit, Gas

  • Top Assembly
    3 Results
  • Gas Controls
    3 Results
  • Blower Assembly (plenum)
    3 Results
  • Wiring Information
    3 Results
  • Supplemental Information
    3 Results
Find part by diagram >

Question and Answers

Q:

Bad spark module on range? JGD8430ADS

A:

Good morning... I can fully understand your concern regarding this issue and you could let that burner dry for a couple of days and see if that will resolve your problem. I will forward your question to an expert who will investigate the matter further and get back to you.You will hear from them within two business days if not sooner. Until you hear from us, have a nice day.

Read More
Henry -
December 30, 2012
A:

Thanks! It's had about a month to dry, thanks to my procrastination. I've considered trying to clean it but don't understand well enough how it works to do so. Appreciate your help!

Read More
Matt -
December 30, 2012
A:

Cleaning the switch on that control valve will probably not help. Since the switch has had enough time to dry out and it is still not working, I recommend that you replace it. You can order the switch from this page: JennAir Cooktop Model JGD8430ADS Control Parts . There is a different part number for the left side burner switches and the right side burner switches. The replacement switch for the left side is part number 74010857. The right side switch is part number 74010858.

Be sure that you unplug the range or shut off the house circuit breaker to completely disconnect electrical power before accessing internal components. Also, shut off the gas supply to the cooktop. I posted some access procedures in the image below in case you need that information for this repair.

If you need more help, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
January 02, 2013
A:

Thanks, Lyle, much appreciated!

Read More
Matt -
January 02, 2013
See more answers
Q:

My stove top is getting no electricity - the electric pilot starters and the exhaust fan don't work.

A:

Diagnosing electrical problems can be difficult. The expert will review your range model and respond. If after hearing from the expert you decide you would like to schedule a technician to visit, an option is the Sears Home Services scheduler in the link below.

Read More
Barbara H. -
September 17, 2011
A:

Thank you for your question and I understand your concern.

Based on your symptom and details it sounds like the cook top is not getting any voltage. When the power was restored the cook top igniters and exhaust fan should have operated normally again. Did you verify the electrical outlet has power? Test the outlet by plugging in some other type of small electrical appliance (hair dryer) to see if the electrical wall outlet has power. If if does not have power, check for a tripped circuit breaker in house breaker box.

I'm sure once the outlet has power that your cook top will work again because a power outage would not likely cause a failure within the cook top.

This may be the issue. If not, please reply and I will be glad to assist you further.

Read More
Joey S -
Sears Technician
September 20, 2011
See more answers
Q:

Can't turn off the ignitor on my Gas Range

A:

Providing a model number to your question will definitely help an expert better your search. If you would like to reply to this thread with a model number included I would be more than happy to assist you. Have a nice day!

Read More
Alina F. -
April 09, 2011
A:

JGD8430ADS is the model number. Four Burner, Jenn Air, downdraft electric range. Took me a while to find the model number. Thanks for your help !

Read More
Jody -
April 09, 2011
A:

Thank you for your question and I understand your concern.

Based on your symptom it could have a faulty igniter switch, the igniter switch has may have slipped off the top of the gas valve or it could have a faulty re-ignition spark module.

In order to check and access the burner/spark switches will require removing the cook top from its installation and then removing the main top.

If you do not feel confident repairing this problem yourself, then you can have it repaired at your home by a Sears technician. Here is a link for the website: Sears Home Services .

Read More
Joey S -
Sears Technician
April 11, 2011
See more answers

Top Parts