Model #JGBP35BEA9BB GE Free Standing, Gas

  • Gas & Burner Parts
    3 Results
  • Control Panel & Cooktop
    3 Results
  • Body Parts
    3 Results
  • Door & Drawer Parts
    3 Results
Find part by diagram >

Question and Answers

Q:

GE Gas Range Model JGBP35aBEA9BB XL 44- SPECTRA Lifting the cook top

A:

I know how important it can be to get instructions on lifting the top on the GE range to clean under it. Please re-verify the model number to get the best possible answers. The link provided below may be helpful. When you get the model number off the range, you may also look for a manual in the other link provided or just click on reply to continue the thread.

Read More
Anna T -
January 09, 2013
A:

hmm, i put the model number in the orginal question JGBP35BEA9BB XL44 SPECTRA GE GAS RANGE

Read More
Dawn -
January 09, 2013
A:

not sure where the a came from in the number!! must have been a typo sorry!!

Read More
Dawn -
January 09, 2013
A:

Here is a link for the owner's manual for that range: Owner's Manual . I posted a procedure for lifting the cooktop in the image below. You will need to remove the grates and burner caps off. You should find screws on each burner as shown below. Once you remove those screws then you should be able to release the clips and lift up the cooktop. Be sure that you unplug the range (or shut off the house circuit breaker) and shut off the gas supply before lifting that cooktop.

If you need more help, let us know.

Read More
Lyle W -
Sears Technician
January 11, 2013
A:

Here is the image.

Read More
Lyle W -
Sears Technician
January 11, 2013
See more answers
Q:

my gas stove oven doesn't heat up. The burners on the stove and the broiler all work fine.

A:

I can understand your concern when it comes to your gas stove, As a suggestion to help you get a detailed answer from the expert is providing the model number to the stove so the expert can do a better diagnose. Just add it to this thread. I have also provided you a link below to Manage my life were a customer posted a similar question like yours that may be helpful to you. Hope it helps!

Read More
Maira E -
September 12, 2010
A:

The stove is a GE XL-44 self cleaning.

Read More
rwine77 -
September 13, 2010
A:

The oven safety valve or the pressure regulator has a shut off valve for the oven built in it. If anyone has done anything to the pressure regulator or oven safety valve, the shut off valve might be closed.

Check the ignitor inside the oven to see if it glows bright red when the oven is turned on. If the ignitor is red the oven controls are sending voltage to the ignitor and oven safety valve. Either the oven safety valve or the ignitor might be bad.

Someone needs to measure the voltage between the white wire on the oven safety valve and the yellow wire on the ignitor. The voltage should read 120 volts ac.

If 120 volts ac is being supplied to the ignitor and the oven safety valve and the ignitor is red someone needs to measure the amps drawn by the ignitor. The ignitor should draw 3.4-3.6 amps in order for the oven safety valve to open.

If the ignitor is drawing 3.4-3.6 amps and the oven safety valve is not opening, the oven safety valve is bad. If the ignitor is drawing less then 3.4 amps, the ignitor is bad.

Read More
Jimmy K -
Sears Technician
September 13, 2010
A:

How do you check the ignitor amps and the safety valve amps. My ignitor has a white color when it is on. Should it be red? I have a GE spectra xl 44 Model JGBP35BEA9BB. Thanks for any additional help you can provide.

Read More
johnfelts -
June 06, 2012
A:

johnfelts,
I will be happy to assist you. The L1 side of the ignitor should have a yellow wire connected to it. You should place your amp clamp on this wire to check the amps. Then turn the oven on and observe the amp reading. If you do not have a minimum of 2.9 amps after a minute, look at the ignitor. If it is glowing, the problem is most likely a faulty ignitor. I posted two images below to aid in the diagnosis. Just click on the images to enlarge them. If you need to order the part for the oven, you can do so from the foll0wing link. Kenmore oven parts
Please let me know if you need further assistance.
Thank you for using Manage my life.
Mark

Read More
Mark T -
Sears Technician
June 07, 2012
A:

thanks I learned to pull out the bottom drawer to access the wiring. The amp reading was 2.84 so I have ordered an ignitor. thanks!

Read More
johnfelts -
June 09, 2012
A:

John,
It sounds like you have it figured out. Please let me know if you need further assistance. Mark

Read More
Mark T -
Sears Technician
June 10, 2012
See more answers
Q:

GE SPECTRA XL 44 MODEL-JGBP35BEA9BB heats up but does not maintain the correct temperature

A:

Maintaining correct temperature is critical to most baking needs. I was able to locate a previous post with information that may help while you wait for the expert response. If you need help to check the oven and set correctly, a technician from Sears Home Services can be scheduled from the link below. I hope this information helps get the oven regulated.

Read More
Barbara H. -
June 02, 2012
A:

I know that it can be very difficult to have issues with your range. You could have a bad thermostat, a failed igniter, an open gas valve or a wiring failure in the ignition circuit that could be causing this problem. If you have a volt/ohm meter, you can unplug the range and check the continuity through the thermostat with it set to heat. If you measure continuity through that component, you can check the resistance of the gas valve. The gas valve should measure about 1.5 ohms. If the gas valve is okay, you can check the resistance through the igniter. The resistance through that component will vary. If you read Ol (open load or infinite resistance) then the igniter is bad and will need to be replaced. If you would like to order parts, just click on this link: Sears Parts Direct . If you need further assistance, please reply to this thread. Thank you for using Manage My Life.

Read More
AnneJ -
Sears Technician
June 04, 2012
A:

Thanks for your reply. If possible, I need some more details. Where is the thermostat? What does it look like? I checked the probe inside the oven and it tested okay. I tested the ignitor and it tested okay. What does the gas valve look like? How exactly do you test the resistance? Do I need to remove the back plate to see the gas valve and thermostat? Any additional help is greatly appreciated.

Read More
johnfelts -
June 06, 2012
See more answers

Top Parts

Recommended maintenance parts & accessories