Model #IGS5000RQ0 INGLIS Residential Dryer

  • Top And Console Parts
    3 Results
  • Cabinet Parts
    3 Results
  • Bulkhead Parts
    3 Results
  • 8318272 Burner Assembly, Optional Parts (not Included)
    3 Results
Find part by diagram >

Question and Answers

Q:

IF the part i need is not named heating element what other name what other name could it be IGS5000RQ0 Inglis Residential dryer

A:

Thank you for choosing SearsPartsDirect.com and for contacting us with your questions about your Inglis dryer model IGS5000RQ0. I am so sorry you are having problems with it. This model does not use a heating element. They are only used in electric dryers.  Your model is a gas dryer and uses a burner assembly. I have included the link below for you to view the parts diagrams online. The Burner Assembly diagram will show you the parts that produce the heat in your dryer. 

When ordering parts, make sure you order the parts for the type of gas supplied to the dryer, either natural gas or propane. 

SAFETY WARNING: Disconnect the gas and power supplies before beginning your repair, to prevent the risk of dangerous gas leaks and the risk of electrical shock which can result in property damage, serious personal injury or even death. Internal parts may have sharp edges. Use caution and wear work gloves to prevent serious cuts. If you are not comfortable completing this repair, you can set up service at www.SearsHomeServices.com or by calling 1-800-469-4663 (1-800-4MY-HOME).

I hope this answers your question. Thank you for choosing Sears, we appreciate your business. 
 

Read More
Rachel Morgan -
Sears Technician
August 11, 2015
Q:

Heat shuts off. IGS5000RQ0 Inglis Residential dryer

A:

It is likely that you have weak gas valve coils (kit part 12001349). 

 

There is a possibility that you have a restriction in the exhaust air flow to the outside of your home. I recommend that you check that first. If you find no problems there, then I recommend that you perform these steps: 

 

There is an observation port on the left side of the front panel under the dryer door. Load the dryer with a medium load of wet towels. Pull the observation port cover and start the dryer on the heated cycle. You can look through the port and see the burner assembly. The igniter will glow and then you will hear a click as it shuts off and the burner lights. The dryer will run for a while with the burner lit and then the burner will cycle off. When the burner tries to re-ignite, the igniter will likely fade off but the burner won't light since the gas valve coils are too weak. They are strong enough to light the burner from a cold start but won't work after they heat up. If you observe this scenario, then I recommend that you replace the gas valve coils.

 

Unplug the dryer and shut off the gas supply before accessing internal components. Pull the lint screen out of the top panel. Remove the two screws that secure the top panel to the lint screen housing. Release the clips under the front sides of the top panel using a putty knife. Lift the top panel up and prop it safely against the back wall. Unplug the door switch (don't forget to plug it back in on reassembly). Remove the screws from the inside top sides of the front panel that secure it to the frame. Carefully pull the front panel off (the drum will sag down). This will give you access to those valve coils. Remove and replace the valve coils and reassemble the dryer.  Note: If you are not completely confident that you can safely complete this repair, I recommend that you have a service technician examine and fix the dryer. Here is a link for service: Sears Home Services Dryer Repair.

 

If you need more help, let us know.

 

Thanks for using Sears PartsDirect. 

Read More
Lyle W -
Sears Technician
November 01, 2013
Q:

dryer

A:

I know how important it is for your o have your dryer working properly in order to complete your laundry. I researched your question and was able to find a link that will give you good information regarding your dryers issue. I attached the link below. I hope this helps.

Read More
Jackie S -
March 15, 2012
A:

Based on your symptoms, you probably have weak gas valve coils on that burner. A blown thermal fuse would prevent the dryer from heating but it would not reset. Since your details indicate that the dryer will initially heat, those components that you mentioned are likely okay. The gas valve coils are apparently working okay until they heat up. Once the dryer is running for a while, they are apparently too weak to open the gas valves for ignition. Replacing those gas valve coils will probably fix your problem. There is a kit available that hose both coils. It is part number 279834. Here is a direct link for that kit: Gas Valve Coil Kit for Inglis Dryer model IGS5000RQ0 . Here is a link for a video that shows how to replace those coils: Dryer Gas Valve Coil Kit Replacement .

I hope that this information helps you repair that dryer failure. If you need more assistance, reply with additional details.

If you get to the point where you need to have a service technician diagnose and repair this failure, you can schedule service through this link: Sears Home Services .

Read More
Lyle W -
Sears Technician
March 16, 2012
See more answers

Top Parts