Model #GWH RHEEM Furnace/Heater, Gas

  • Model Number Notes
    3 Results
  • Replacement Parts 1-38
    3 Results
  • Replacement Parts 27-41
    3 Results
  • Replacement Parts 39-42
    3 Results
  • Replacement Parts 39-45b
    3 Results
Find part by diagram >

Question and Answers

Q:

cONTROL PANEL KESC307GWH1 Kitchenaid 30" slide-in range

A:

Hello glad to help.  Thank You for choosing Sears PartsDirect.com

I am sorry and do understand your frustration when having trouble with the range. 

Glad to help out.   Im  looking at your Kitchenaid model number KESC307GWH1.

On this code F2:E5 that I have checked.  Says Cancel key drive line is open.  

1.  Flip circuit breaker.

2.  Check keypad connectors for a firm/tight connection.  (Keypad connecting to the control board).  (check the wiring to see if any is split).

3.  Press the "Cancel".  If the error code returns after 60 seconds then you need to replace keypad.  (On your model it is called the electronic control).  

 I have on the link below the electronic computer board.  

control board for model KESC307GWH1 

 If you have further questions please let me know.

Thanks for choosing Sears PartsDirect.com

 

Read More
Larry L -
Sears Technician
October 07, 2013
Q:

Problem replacing gas burner in kitchenaid cooktop

A:

I know this type of information can be very helpful for you to have.  While you are waiting for your expert answer, I did some research on the model and part number.  I was unable to locate information that would be helpful with regards to your question at this time.  Your expert will answer within two business days.  Thank you for using Manage My Life.
 

Read More
Yadira B -
July 30, 2013
A:

thanks

Read More
Eric -
July 30, 2013
A:

Thank you for your question and I understand your concern.

I do not have a clear or full understanding of which screws and which support bracket you are referring to. I thought you purchased new screws specifically for the burner heads? The burner head screws are different from the orifice holder screws. The new burner heads will likely use self-tapping screws if there are no threads already cut in the new burner heads. 

I added an image below to reference. I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post.


Read More
Joey S -
Sears Technician
July 31, 2013
A:

Thank you for your reply. In reference to your picture, it would be the venturi mounting screw. I ordered new screws (which Sears says are the correct screws) and new support brackets so I will see if that helps with attaching the venturi. Please let me know if you have any further thoughts. Thanks Eric

Read More
Eric -
August 01, 2013
See more answers
Q:

Access internal components of Kitchenaid cooktop (model kgct305gwh1).

A:

The Managemylife web site is a good resource of information to find out what may be happening and what options are available to you. I'm sorry to hear about the difficulties with your KitchenAid cook top. I did some research at Managemylife website and found this expert answer to a similar question that may help until your expert can respond. I have attached the link below so you can check it out. I hope this will assist you Steve until your expert can respond to your specific question.

Read More
James -
April 20, 2013
A:

Thank you for your question and I understand your concern.

 I added an image below showing the procedure to access the spark module. The glass top will have to come off. You will need to remove all the knobs, all the small screws at each sealed burner and remove the drip pan, disconnect the wires connected to each electrode then the burner base. 

Foam tape is used between the bottom of the glass and the counter top to prevent any spillage from running past the cooktop. You should be able to leave the foam tape and simply re-install the cooktop after replacing the spark module.

Be sure turn off the gas and disconnect the power cord and gas line before removing the cooktop. 

 I hope this is helpful. If I may be of further assistance as more details become available, please reply to this post. 

 

Read More
Joey S -
Sears Technician
April 22, 2013
See more answers